Kenmore Dryer 110.C85089400 (110C85089400, 110 C85089400) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3387242
The Front Panel Seal is an OEM replacement part for Whirlpool dishwashers. Measures 24 inches. This seal is located on the dishwasher's front panel and helps prevent water leaks by creating a watertight barrier during the wash cycle. It ensures efficient operation while protecting your kitchen from potential water damage.
Symptoms of a bad Front Panel Seal include:
- Water leaking from the front of the dishwasher during operation
- Visible wear, cracks, or tears in the seal
- Increased noise or vibration due to improper sealing
Causes of a failing Front Panel Seal can include wear and tear from regular use, exposure to high temperatures and moisture, or improper cleaning methods. A damaged seal can compromise the dishwasher’s efficiency and lead to water leakage.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, 2 seals are required on front panel.
Do-It-Yourself Stories from Customers like You
Squeaking kenmore dryer that stopped working Paul M. • Norcross , GA • November 28, 2016
First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything...
Read more
More
$19.95
- Compare At:
-
$23.74
- You Save:
-
$3.79
Genuine Whirlpool part
By: Whirlpool
Part Number: W11236646
The washer is an OEM replacement part for Whirlpool clothes dryers. This part is located on the drum roller support shaft in your dryer. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.
Causes can be normal wear to bearing surfaces over extended use cycles. Accidental impacts may also potentially bend or damage shaft components.
Symptoms of a bad roller shaft include:
- Noisy squeaks or clanks emanating from within
- Jerky or unbalanced tumbling of dryer loads
- Roller assemblies binding or sticking
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Roller broke Art M. • Danville , CA • September 23, 2014
Replaced the roller, shaft, rings and washer. After removing the back, reverse threading the nut off, discarding the old hardware and installing the new hardware back in business in about 20 minutes.
Read more
More
$21.95
- Compare At:
-
$26.34
- You Save:
-
$4.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3388229
The Access Panel Spring Retainer is an OEM part for Whirlpool dryers. This part secures the access panel of the dryer, ensuring it stays in place during operation. The spring retainer provides tension and stability, making it easy to open and close the access panel when maintenance or repairs are needed.
Causes of a bad access panel spring retainer can include regular wear and tear, loss of tension, or physical damage.
Symptoms of a bad access panel spring retainer include:
- Access panel not staying securely closed
- Difficulty opening or closing the access panel
- Loose or rattling access panel during dryer operation
- Visible damage or wear on the retainer
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer no start George Larry B. • Niceville , FL • November 19, 2019
Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now.
Read more
More
$9.41
- Compare At:
-
$11.20
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP308685
Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.
Do-It-Yourself Stories from Customers like You
Under the counter mounting brackets were missing Douglas A. • Glen Allen , VA • June 19, 2019
After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day.
Read more
More
$7.31
- Compare At:
-
$8.63
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: 279393
Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.
Do-It-Yourself Stories from Customers like You
Dryer would not turn on. Keith K. • Melbourne , FL • May 19, 2020
And after replacing the thermal fuse The dryer turned on.
Read more
More
$29.95
- Compare At:
-
$35.64
- You Save:
-
$5.69
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3389420
Secures the idler pulley to maintain proper drum belt tension in your dryer. Replace if worn, loose, or causing squealing noises. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Loud squealing noise when dryer (Whirlpool) is turned on Marc P. • Chesterfield , MI • December 31, 2018
Using You Tube How-To Videos.
Replaced the drum drive belt and tensioner pulley/arm (including) the spring.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: 279318
Includes screws and wire connectors. For the complete terminal block kit use 279320.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Loose wire in back caused a short and burned out plug insulator etc William W. • Pottsboro , TX • February 15, 2019
I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great.
Read more
More
$56.95
- Compare At:
-
$67.20
- You Save:
-
$10.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8283288
Comes with jumper wire.
Do-It-Yourself Stories from Customers like You
Drier would not start when i set it to diagnostics code said 6e all display lights turned on Randal B. • Salt Lake City , UT • December 21, 2014
Searched internet for answers. Decided to replace the door switch. Drier now runs great!
Read more
More
$81.95
- Compare At:
-
$97.52
- You Save:
-
$15.57
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3406653
This sensor harness connects the dryer's moisture sensor bars to the main wiring, helping the control or timer read moisture levels so Auto Dry cycles can advance and deliver consistent, reliable drying performance.
- Provides the electrical path between the moisture sensor bars and the control/timer
- Enables the dryer to sense wet fabrics and adjust or advance Auto Dry cycles
- A damaged or open harness can cause Auto Dry to not advance, run too long, or stop early
- Contribute to inconsistent dry times or a "Sensing" indicator that behaves abnormally
What's included: One sensor wire harness Install notes:
- Disconnect power before servicing
- Access the sensor bars at the front bulkhead; note wire routing and clip locations
- Transfer routing/clips from the old harness; connect to both sensor bars and the main harness plug, ensuring snug terminals and clear wire paths
- Restore power and run an Auto Dry test; inspect/clean the sensor bars and check harness continuity
Do-It-Yourself Stories from Customers like You
Dryer turning off on auto cycle with clothes still damp Mark F. • Topsham , ME • January 31, 2015
Replaced 3 low cost parts as advised by Appliance Parts Pros. Saved the labor costs by troubleshooting and replacing parts with their great videos. Works like new, and took 15 minutes to complete the repair.
Read more
More
$78.95
- Compare At:
-
$93.16
- You Save:
-
$14.21
Genuine Whirlpool part
By: Whirlpool
Part Number: 279782
Dryer won't start but has power and timer works? This belt switch kit stops the dryer when the belt breaks. Moderate DIY repair, 45-60 minutes.
Do-It-Yourself Stories from Customers like You
Broken belt switch Jack F. • Hermosa Beach , CA • July 08, 2016
Every time I tried to start our dryer, the "Sensing Light" came on, I heard a little "click," and the dryer would not start.
According to the very helpful Appliance Parts Pros. videos, I was able to dismantle, diagnose a few components, and discover the broken part. In this case, it was a Broken Belt Switch.
I ordered the part, we went on vacation for a week, and when we returned home the part was at our residence. The next day, I installed the part and all is good now.
I am nearly 70 years...
Read more
More
$52.95
- Compare At:
-
$63.01
- You Save:
-
$10.06
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693995
This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.
Do-It-Yourself Stories from Customers like You
There was no power cord and accessories to attach it Terry C. • Martin , TN • December 27, 2016
I put all pieces that I ordered on the dryer and plugged it in.
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: W10802681
Dryer not heating? A warped or damaged heater box lets heat escape, reducing efficiency. This housing secures the element and protects components.
Do-It-Yourself Stories from Customers like You
Heater element bad Paul R. • Lewisville , TX • January 09, 2017
Well i thought i had to replace the whole metal casing, turns out the element is separate and that was all i would have needed. but i cot my original casing apart only to find out that was a mistake. anyway i got it all repaired now and its working like new.
Read more
More
$85.95
- Compare At:
-
$101.42
- You Save:
-
$15.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359452
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Do-It-Yourself Stories from Customers like You
Whirlpool washer was shaking and moving in spin cycle Charles B. • Sioux Falls , SD • September 25, 2018
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10109200
This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.
- Fastens panels, brackets, or internal parts to the cabinet/frame
- Helps maintain alignment to reduce vibration and rattling
- Replaces lost, stripped, or corroded screws
- Common symptoms: loose panels/trim, rattles, or a screw that won't tighten
What's included: One screw. Install notes:
- Disconnect power; shut off water or gas if applicable
- Match thread and length to the original; replace one at a time to keep alignment
- Start threads by hand to avoid cross-threading; use the correct driver
- Tighten snugly—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Missing baffles Anna S. • Shoreview , MN • January 31, 2016
I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3393657
Dryer belt slipping off motor pulley or making squealing noises? The belt restrainer keeps the drive belt aligned. Moderate DIY repair with video guide.
Do-It-Yourself Stories from Customers like You
Loud squealing noise when dryer (Whirlpool) is turned on Marc P. • Chesterfield , MI • December 31, 2018
Using You Tube How-To Videos.
Replaced the drum drive belt and tensioner pulley/arm (including) the spring.
Read more
More
$73.40
- Compare At:
-
$87.35
- You Save:
-
$13.95