Kenmore Refrigerator 363.9537751 (3639537751, 363 9537751) Parts
Genuine Ge part
By: Ge
Part Number: WR30X30972
Ice maker not producing ice or won't dispense cubes? This complete ice maker assembly replaces failed units. DIY-friendly install in under 10 minutes.
Do-It-Yourself Stories from Customers like You
Ice maker would not exspell the ice after it was made. Leesinger K. • Jackson , WI • April 03, 2014
I found that the Ice Maker in my GE side by side made ice but would not kick out the ice when it had formed, the heating element or the switch that controls it didn't work. I ordered a new ice maker switched it out took less than 3 minutes. The cord was very stiff and just long enough but I got it to connect and in 35-40 minutes I had fresh ICE!!
Read more
More
$190.62
- Compare At:
-
$226.84
- You Save:
-
$36.22
Genuine Ge part
By: Ge
Part Number: WR2X8474
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
This part fixes the following symptoms
-
Leaking
-
Ice maker not making ice
See more...
Do-It-Yourself Stories from Customers like You
Had a cracked plastic ice maker inlet water tube that flooded part of kitchen floor Terry C. • Durham , NC • February 16, 2019
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,...
Read more
More
$32.95
- Compare At:
-
$38.88
- You Save:
-
$5.93
Genuine Ge part
By: Ge
Part Number: WR51X443
Ice buildup in freezer? This defrost heater and thermostat assembly melts frost from evaporator coils. Moderate DIY repair restores proper cooling.
Do-It-Yourself Stories from Customers like You
Defrost heater not working Jayesh P. • La Canada , CA • June 12, 2014
I replaced defrost heater with thermostat. It is a very easy and there is YouTube tutorial video for that.
Read more
More
$117.34
- Compare At:
-
$145.61
- You Save:
-
$28.27
Genuine Ge part
By: Ge
Part Number: WR62X26536
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
- Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
- Helps maintain a proper seal to limit frost and moisture around the dispenser
- Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
- Wear or sticking of the armature/spring can hinder movement and affect dispenser operation
What's included: 1 armature kit Installation notes:
- Unplug the refrigerator and shut off water to the dispenser before servicing
- Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
- Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
- Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation
Do-It-Yourself Stories from Customers like You
Water was overflowing out of the ice maker during fill process and freezing into a block of ice! Steven B. • Arlington , TX • March 17, 2015
Replaced the water supply valve...boom!
Read more
More
$54.95
- Compare At:
-
$65.94
- You Save:
-
$10.99
Genuine Ge part
By: Ge
Part Number: WR2X8818
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
- Holds the recess/ice door on its pivot within the dispenser assembly
- Helps the flapper close fully to seal the ice chute
- Restores smooth open/close action of the dispenser door
- Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute
What's included: 1 recess door retainer Install notes:
- Unplug the refrigerator before servicing the dispenser
- Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
- Note spring orientation and retainer position; transfer components to the new retainer
- Verify flapper movement and seal before reassembly and restoring power
Do-It-Yourself Stories from Customers like You
Yes ice was not coming out of the dispenser Jason S. • Goose Creek , SC • December 02, 2014
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well.
Read more
More
$6.72
- Compare At:
-
$8.36
- You Save:
-
$1.64
Genuine Ge part
By: Ge
Part Number: WR62X107
Door solenoid with plunger.
Do-It-Yourself Stories from Customers like You
When dispensing ice from the ice maker, the solenoid was buzzing loudly. It was also rusting badly. Brian B. • Hudson , NH • March 28, 2014
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside....
Read more
More
$72.38
- Compare At:
-
$86.13
- You Save:
-
$13.75
Genuine Ge part
By: Ge
Part Number: WR60X10262
This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.
- Drives the ice auger/crusher to feed ice from the bucket through the dispenser chute
- Helps deliver cubes or crushed ice, depending on the control selection
- Common symptoms: no ice dispensing, auger not turning, loud humming or grinding, intermittent or weak dispensing
- Located in the freezer-door dispenser assembly and engages the ice bucket coupler
What's included: One dispenser crusher motor. Install notes:
- Disconnect power to the refrigerator before servicing
- Remove the ice bucket and dispenser trim/panel to access the motor; note wire orientation and fasteners
- Transfer any mounting hardware or coupler from the old motor
- Reassemble, restore power, and test ice dispensing
Do-It-Yourself Stories from Customers like You
Needed new ice maker motor and circuit board Edward Z. • Berlin , CT • August 19, 2016
I watched the help videos first, then ordered the parts, and installed all items as in the video.
Read more
More
$147.95
- Compare At:
-
$176.06
- You Save:
-
$28.11
Genuine Ge part
By: Ge
Part Number: WR23X10300
Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.
Do-It-Yourself Stories from Customers like You
Power cord needed to be replaced Jorge V. • Tucson , AZ • November 14, 2015
Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR01X10618
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Do-It-Yourself Stories from Customers like You
Ice dispenser wouldn't dispense ice Chris K. • Felton , DE • April 29, 2025
The auger gearbox shaft had a spot that was stripped of threads which prevented the auger drive from spinning the ice down the chute. I replaced the auger motor/gearbox assembly, the auger drive as it had to be cut off the shaft, and the 3 mount bolts that hold it all in place. Whole job took 30 minutes from start to finish which included cutting off the drive bracket.
Read more
More
$7.95
- Compare At:
-
$9.46
- You Save:
-
$1.51
Genuine Ge part
By: Ge
Part Number: WR1X1367D
Includes 12 retainer rings.
Do-It-Yourself Stories from Customers like You
A fin on the plastic auger broke off and needed to be replaced John M. • Massanutten , VA • August 08, 2015
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went...
Read more
More
$13.79
- Compare At:
-
$16.41
- You Save:
-
$2.62
Genuine Ge part
By: Ge
Part Number: WR1X5278
Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.
More
Genuine Ge part
By: Ge
Part Number: WR2X7309
This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.
- Secures the solenoid to its housing or frame to prevent shifting
- Maintains proper alignment for reliable actuation
- A worn or broken saddle can cause buzzing/chattering and intermittent operation
- Restores stable mounting to help the connected mechanism work correctly
What's included: 1 solenoid saddle Install notes:
- Disconnect power; shut off water supply if working near water lines
- Access the solenoid assembly and note the original saddle's orientation
- Transfer the solenoid into the new saddle and reuse existing fasteners/clips
- Smooth operation before reassembling panels
Do-It-Yourself Stories from Customers like You
Ice dispenser crushing ice only no cubes Eric W. • Copper Canyon , TX • June 27, 2014
Easy fix once I found the problem. Broken solenoid sleeve. Part cost $2.58 + shipping. 10 minute repair.
Read more
More
$7.95
- Compare At:
-
$9.46
- You Save:
-
$1.51
Genuine Ge part
By: Ge
Part Number: WZ4X241D
Includes 12 screws. Size: 8-18 ab.
Do-It-Yourself Stories from Customers like You
We didn't have a power cord for our dryer Heather B. • Dulce , NM • October 27, 2018
Ordered the cord through appliance parts pros, with additional screws and it works! Yay after waiting months and everywhere was out. Thank you.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR2X4138
Mounting spacer maintains proper clearance between refrigerator panels, doors, or components. Replace if cracked, broken, or missing to restore fit.
More
$15.41
- Compare At:
-
$18.34
- You Save:
-
$2.93
Genuine Ge part
By: Ge
Part Number: WR2X7905
Seals the ice bucket to prevent spills, frost buildup, and water pooling. Replace when ice shifts or water collects. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
The augor in the ice maker was rusty Angie K. • Greenwich , CT • November 15, 2015
Changed the part with SS part.
Read more
More
$10.07
- Compare At:
-
$11.94
- You Save:
-
$1.87
Genuine Ge part
By: Ge
Part Number: WR01X10623
Replacement 8-18 x 9/16 machine screw for securing panels, brackets, and internal components. Needed when fasteners are stripped, missing, or worn.
Do-It-Yourself Stories from Customers like You
Ice maker internal door not closing John M. • St. Augustine , FL • January 12, 2016
Originally replaced the door and spring but it still would not close. This time, replace the solenoid and it works great!!!
Read more
More