Kenmore Refrigerator 596.65232402 (59665232402, 596 65232402) Parts

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

• Not dispensing water
• Ice maker not making ice
• Leaking

I watched your how-to video. It explained the repair PERFECTLY. It was an easy repair and the video was very detailed. It took the guesswork out of the repair. I was done in 5 minutes. thanks for taking the time to post videos for your parts. I'll shop here again. Best Regards, Chad M Read more

Ordered and paid for two day shipping and received on time. Read more

I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more

I had verified that the water supply was healthy, so it was either the icemaker unit or the water valve. I replaced the icemake first, based on a the pareto showing it was the culprit for most other people, but it didn't help. That replacement was straightforward; the hardest part was reaching all the way back to unclip the wiring harness since I am too lazy to totally empty the bottom freezer and remove the door. So the next step was the water valve. The hardest part of this was pulling the... Read more

My son broke the bottom shelf on the refrigerator door. I found the model number inside the frig and within 5 mins the part was on it's way! Ordered it Saturday morning , and arrived on Monday! Too easy! Slipped right into place! Read more

Replaced the gasket . Parts were were here one day after ordered . U-tube video was a big help. Went faster and easier than expected . Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

Replaced the ice level arm Read more

First had to clean inside the empty freezer, that was the hard part. removed old gasket and cleaned inside the track in the door. had the new gasket well warmed and in the right shape. put new gasket in track. seating it firmly. It was very easy. I did watch a couple of online videos to get the general idea of what it detailed. While I was at it I cleaned the coils with the brush I also bought with the gasket, worked great. all in all if you get organized before hand and take your time,... Read more

Replaced icemaker and shutoff arm. Easy project. Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

There is nothing you can't do given the right YouTube video! We disassembled the bottom mount freezer n our Jenn Air refrigerator to remove all the ice and then located the clogged grommet on the back of the unit and cleared it and added a notch. In the process of reassembling we broke the bracket on a part that should have been the easiest portion of the entire installation! In seconds we located and ordered the part on your site. It arrived in a couple of days and then we removed the door and... Read more

Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find... Read more