Kenmore Refrigerator 596.76589600 (59676589600, 596 76589600) Parts

Looked up parts based on fridge model number, watched videos, and replaced parts using just a few tools... easy. Parts came quick, well packaged. After 16 years, plastic parts deteriorate and break. The fridge was operating fine, but the drawers and covers were failing. Much cheaper to replace a few parts ($$-$$$) than buy a new fridge ($$$$). The new parts matched up exactly to old ones. The videos were very helpful, but not perfect... for the Crisper Frame, there was a structural metal... Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Ordered the piece and put it in the refrigerator. Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

First, I did online research to find out what could be the problem with these symptoms of cold freezer and warm fridge. I found multiple posts with people going back and forth as far as what to do to fix it. One tread even provided the link to your store with the part number for the evaporator fan motor. So I did the inspection of the motor as suggested by the expert and sure enough it was the evaporator's motor fan that was not working as it should. That is when I immediately follow the link... Read more

I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more

Replacement of parts found on this site- great explanation and pictures as shown! Read more

There are videos on You Tube,. After removing the bottom basket, you remove the entire drawer including the door together with it, by using a screwdriver to depress the white clip on each drawer slide which releases the slide from body of the freezer. Once you pull our the entire drawer, you will need to drill out a rivet to remove the old slide. You will need a rivet gun to attach the new slide. Read more

I had verified that the water supply was healthy, so it was either the icemaker unit or the water valve. I replaced the icemake first, based on a the pareto showing it was the culprit for most other people, but it didn't help. That replacement was straightforward; the hardest part was reaching all the way back to unclip the wiring harness since I am too lazy to totally empty the bottom freezer and remove the door. So the next step was the water valve. The hardest part of this was pulling the... Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

Replaced the ice level arm Read more

Read most possible causes on AppliancePartsPros website. After deciding on a course of action, I ordered the parts with expedited shipping, received them next day, installed them on same day received and everything is working fine. Congratulations to them for possessing and offering such an excellent diagnosis tool for the DYIer. It has worked well for me many times in the past. I would never hesitate to recommend them as I feel they are a first rate organization. P.S. - Their excellent... Read more

New mounting screws and handle. BTW, the parts have been redesigned to be more robust. Easy fix and the Refrigerator// Freezer look like new. Read more

• Freezer not defrosting

After we moved into our new home, we realized that the freezer was very cold and the fins were frosting over, and the refrigerator wasn't cold. We had to take it apart and manually defrost it about once every 8 to 10 days. After research online, we found Appliance Parts Pros videos, which clearly explained how to fix it ourselves, a savings of at least $1,000 or more, since a new one of this size would have been in the arena of $1,200 to $2000. We ordered the three most likely parts to be bad,... Read more