Kenmore Range 629.60008601 (62960008601, 629 60008601) Parts

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

• Door won't open or close

The replacement hinge unit arrived in just two days. The JennAire (Maytag) oven door is fairly typical in that it easily lifts off of the hinge bars. Once the door is off then removing two screws is all that's required to remove the hinge unit from the oven. The new hinge slides up into place and while you hold it up inside of its location putting the old screws back in is very easy. After sliding the door back down onto the hinge bars the oven is as good as new Read more

I ordered the replacement light module and install it. I was able to install the module without removing the walloven from the cabinet. Thank you for quick delivery of the module. Read more

First, watched a how to you tube video. Then, proceeded to repair my stove. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more

I ordered the replacement part and undid two screws on the front of the cooktop then used a nut driver to undo the clamps holding the burner in.I took a picture of the wiring then used needle nose pliers to gently pull the connectors off the terminals. reinstalling you just line up the new burner with the old one and screw the clamps back on. there are no predrilled holes the screws just bite into the insulation. Read more

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

Purchased the triple burner and dual burner element. I added my model of stove and I was able to pull up diagrams of the stove parts. The parts were easy to find using the diagrams and the burner elements were marked 17 & 15 so I placed my order. Parts were here in a couple of days. The tricky part was figuring out how to get into the stove top. I was a few youtube videos to see different replacement. My husband and I got the stove top off and flipped it over on the counter. We looked at... Read more

Replaced It With New One Read more

Part arrived quickly and was an easy install1 Read more

My customer service/sales rep was very helpful and walked me through the order process. The parts came very quickly with standard shopping and the install was pretty straight forward. I used the Maytag service guide and your videos to do the install. Love your company! Keep up the great work! Read more

Ordered new screws and door gasket. Replaced the old door gasket now the oven warms up faster and bakes the stuff easier. Replaced the missing door trim screws. Now the door close without making noises. Read more

Could not find info anywhere to fix it Pulled out the stove seen a side panel of sorts undid the trim remove side panel switch was right there 15 min tops and everything was working again. The rapid preheat door lock everything. I have a duel fuel so no way do you remove the control panel as some were saying Nope look on the side Really easy fix Philips screw driver and 1/4 nut socket and that's it! Read more

I had to remove the oven door, which I learned is made to come off without tools. Then took out the bottom by removing two screws and lifting. Removed the screws attaching the igniter, pulled wires thru back until I could get the connector and disconnect. When the new igniter arrived, I had to change the connector. I cut the one off the old one, and spliced to the new one using solder and shrink tubing. Just reverse the procedure to install. I replaced the screws with new ones. Read more

I purchased a can of black appliance spray paint, removed the panels on the dishwasher, sprayed them, and a few hours later put them back. They're beautiful and it looks like I have a brand new dishwasher! It now matches everything and looks great with the new granite counter tops I just installed. THANK YOU FOR THE GREAT IDEA!!! I'm a 76 year old female and my friends think I'm a genius! Read more