Kenmore Dishwasher 665.13482K902 (66513482K902, 665 13482K902) Parts

This replacement upper spray arm restores strong spray coverage to the upper wash level of your dishwasher. It channels water through its jets and spins under pressure to help deliver consistently clean dishes on the top rack.

• Directs pressurized wash water to the upper wash level for thorough cleaning
• Rotates under water pressure for even spray coverage
• Helps clear food soils and detergent residue from dishes and glasses
• Common symptoms: poor cleaning on the upper rack, spray arm not spinning, clogged or cracked arm

• Disconnect power and shut off the water supply before servicing
• Open the dishwasher; remove the upper rack if needed for access
• Release or unthread the retainer and pull the old arm straight off; clear debris from the hub/feed port
• Seat the new arm and secure the retainer hand-tight; ensure the arm spins freely and run a test cycle

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

Located between the console and door

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

This is a tine clip, also called a tine row pivot, that is commonly used in dishwashers. It is located in the top dish rack. The tine clip is designed to ensure the tine row stays in the right place in the dishrack. The tine clip is made of durable plastic. It can become cracked or damaged through regular use and cause the tine row to move out of place in the dishwasher. If the part is damaged or broken, it will need to be replaced.Replacing the tine clip does not require any specific tools, but work gloves can be useful. Make sure to unplug the dishwasher and turn off the water supply to the appliance before starting the replacement process. Remove the components that restrict access to the tine clip before pulling the clip out of the dishwasher. The new component can be placed in the same location before reassembly. Turn the power and water back on before use.This tine clip is designed to be used with dishwashers manufactured by Ikea, Kenmore, and Whirlpool. It is sold as an individual product. This is an authentic OEM replacement component that is sourced directly from the manufacturer.

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing

To order seal use WP8268340.

Color: Black.

This dishrack organizes and supports dishes inside the dishwasher during wash cycles. Replacing a damaged rack restores smooth loading, keeps items upright, and helps prevent rust stains or snags from broken tines or flaking rack coating.

• Holds and organizes plates, bowls, and cookware during wash and rinse cycles
• Keeps items spaced and upright to promote spray coverage and drainage
• Slides in and out on the rails when the rack is straight and intact
• Common failure signs: rusting/chipping coating, broken or bent tines, cracked or warped wire frame
• Needed if dishes won't stay put or the rack binds when moving on the tracks

• Disconnect power at the breaker and turn off water before servicing interior parts
• Open the door, extend the rack, and remove rail end caps to release the rack
• Transfer any clip-on components from the old rack to the new rack as needed
• Seat the rack on the rails, reinstall end caps, and check for smooth operation

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

Color: Black

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

This front seal sits at the leading edge of the dishwasher door opening to keep wash water and steam contained. Replacing a worn seal helps stop front-edge drips and protects adjacent cabinetry and flooring.

• Creates a watertight barrier along the front tub-to-door interface
• Helps prevent leaks at the bottom/front of the door during cycles
• Replace if the seal is cracked, flattened, torn, or missing
• Common symptoms: water under the kick panel, damp streaks at the front lip, visible wear

• Disconnect power and turn off the water supply before servicing
• Open the door, remove the old seal, and clean the front lip/channel thoroughly
• Center and press the new seal fully into place without stretching; ensure even compression
• Close the door and run a short test cycle to check for leaks