Kenmore Dishwasher 665.13982K800 (66513982K800, 665 13982K800) Parts

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

Following the very clear and concise Video from AppliancePartsPros.com, I was able to insert the friction pads that had fallen off from the dishwasher door. It now works. The next project may be to replace the rollers of the Dish Rack which are now a little bit worn out. Read more

Just replaced the things. Had to reuse old tine rows, rollers, the spray arm, etc., i.e. I removed 'em from the old racks and put on the new ones, but that was piece of cake. Also, I cleaned the food grinder and the discharge valve compartment (thank you very ???? ???? much, Internet), so spray arms around the top rack get enough water pressure now. I didn't have to buy any parts for the latter part of this little repair project, though. Read more

• Not cleaning dishes properly

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

New door seal did the trick. Read more

Order parts and replace. When removing attachments, do them one at a time and install them on new rack as you go. Watch for the small release tabs on the attachments (baskets, rollers and tine holders), "gently" put pressure to release; remember these units have been in hot water and they are brittle. Read more

Ordered new insulation from AppliancePartsPros. It was delivered quickly and easy to install. Read more

I was repairing my daughter's WDT730pahz0 Whirlpool dishwasher. The bottom dish rack set of wheels was very easy to install. The replacements for the upper set of wheels is different than the originals. In my opinion, the replacements are far superior to the original parts. The problem, as many have pointed out, is that there are no instructions on how to install the new parts. I worked for 15 minutes, attempting to put the pieces together and then install them on the dishrack. That was a... Read more

Touch up paint Read more

Replaced It With New One Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

Just replaced the things. Had to reuse old tine rows, rollers, the spray arm, etc., i.e. I removed 'em from the old racks and put on the new ones, but that was piece of cake. Also, I cleaned the food grinder and the discharge valve compartment (thank you very ???? ???? much, Internet), so spray arms around the top rack get enough water pressure now. I didn't have to buy any parts for the latter part of this little repair project, though. Read more

Repair was easy. Just slotted the new parts in and they fit and worked fine, Read more

Ordered front panel and panel control. Also ordered name plate (did not need) front panel already has it. My husband and I had it switched out in approx 10 minutes. Took longer to gather proper tools than it did to do the repair. Looks awesome and original! Read more