Kenmore Dishwasher 665.15869990 (66515869990, 665 15869990) Parts

I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again. Read more

Ordered the part from Appliance Parts Pros, it arrived about a week later and it was the correct part. I liked the cross reference and confirmation of the correct part that was available on the website before placing an order. Read more

While at my sister's house, she showed me how to access & dismantle the housing unit on her dishwasher, thinking the issue might be from that area. So, when I came home, I opened up my housing unit and found that several of the screws had come out and the pump outlet seal was stretched out and partially outside of the unit itself. I located all of the missing screws & discovered I was still missing one, which my husband helped me order with the pump outlet seal. I easily replaced the old seal... Read more

Replaced upper and lower spray arms, plus nylon bearings. Read more

Replaced the drain & wash impeller kit. Read more

I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached... Read more

Good but it says the tube holder doesn't come with it but it actually does Read more

I ordered a pair of springs from AppliancePartsPros.com. When the new springs arrived, I unscrewed the frame from the counter top, slid the dishwasher out part of the way and installed the new springs and saved myself at least one-hundred dollars. Read more

Part was updated from original equipment (3 pieces) to a one piece tube. Snip the top of hanger loop then install. Just a couple minute job. Updated tube is much better than the original design. Read more

Replaced nut and then found we needed new pump. Read more

Although we had a service contract with Sears I elected to take a quick look to see what was wrong. There were 3 problems: 1 - retainer thumb screw had broken and appeared to have been damaged for some time showing scummy buildup along the line where the threads finally separated from the knob, 2 - after removing the lower spray arm, observed that the pump seal was visibly distended and exposed, and 3 - the 3rd level wash arm spinner disk was in the parts bag and the stainless steel sweat-fit... Read more

I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately. Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it... Read more

This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more

Received correct parts for Appliance Parts with ease and quickly. Read more

Replaced the felt seal and door vent assembly by removing the inside panel of the door and cleaning off the old seal and replacing with the new one. The vent assembly simply snapped out and was easy to replace with the new one. No more leaks and Mother was happy. Removal of the screws required a torx screw driver and someone to hold the door open while the panel was replaced. Easy fix. Read more

Replacement heater element installed exactly as described in the AppliancePartsPros video. Read more