Kenmore Dishwasher 665.17439001 (66517439001, 665 17439001) Parts

Dishwasher door panel insert. Reversible: white color on one side, black on the other.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This fill and drain hose assembly connects a portable dishwasher to a sink faucet, delivering incoming water and routing wastewater back to the sink. Replacing a worn assembly restores a secure connection and helps prevent leaks during operation.

• Integrates inlet and drain hoses with a faucet coupler for quick, tool-free hookup
• Supplies water to the dishwasher and returns drain water to the sink
• Can address no fill or no drain symptoms caused by a damaged or obstructed hose/coupler

• Safety first: Unplug the dishwasher and turn off water before servicing
• Expect residual water; place towels/pan and relieve line pressure
• Ensure a compatible faucet adapter is installed; attach the coupler fully and verify a good seal
• Route hoses without kinks, secure the drain end to the sink, and check for leaks on first run

The Impeller is an OEM part for Whirlpool brand dishwashers. Located within the dishwasher sump assembly, this plastic component utilizes rotating blades to circulate wash water throughout cycles.

Causes of a bad impeller can include cracking or damage from minerals over time, chunks of food debris jamming the blades, or normal wear on plastic.

Symptoms of a faulty impeller include: 

• Inadequate water circulation yielding poor cleaning 
• Food particles or utensils not fully rinsed
• Loud clicking or grinding noises mid-cycle
• Error codes relating to low water pressure

Replacing the impeller restores optimum water flow for Whirlpool dishwashers. Proper circulation using the OEM replacement ensures all portions of dishes and cycles receive sufficient water volume. Compatibility also includes Maytag, Jenn-Air, Amana, Magic Chef, and other brands.

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

Pump housing only. For a complete pump and motor assembly, order WPW10247394.

This dishwasher door spring restores proper counterbalance so the door opens smoothly and doesn't drop. The premium version provides the factory-specified tension used on select models for consistent, controlled door movement.

• Counterbalances the door for smooth opening and closing
• Helps prevent the door from slamming open or feeling heavy
• Supports stable, mid-position hold when springs are intact and matched
• Common signs of failure: door drops quickly, is hard to lift, or won't stay in position

• Disconnect power and water; remove the toe kick/access panel to reach the springs
• Note which frame/hinge holes the old spring used and install the new spring in the same positions to match tension
• Use pliers to relieve tension safely; if your model uses two springs, replace both for balanced operation
• Wear gloves and eye protection; keep hands clear of moving hinges

This felt door vent seal fits around the dishwasher's door vent to help contain steam and moisture within the inner door. Replacing a worn seal helps prevent minor leaks and condensation around the vent area during cycles.

• Creates a gasket between the vent assembly and inner door panel to keep steam directed through the intended vent path
• Reduces moisture escape that can cause drips or water spots on the outer door or nearby countertop
• Helps limit condensation or musty odors from trapped moisture inside the door panel
• Indicators of failure include visible wear or separation of the felt and moisture around the vent during operation

• Disconnect power and turn off water supply before servicing the dishwasher
• Remove the inner door panel to access the vent assembly
• Note the seal's orientation; clean mating surfaces; seat the new felt evenly around the vent with no gaps
• Reassemble and run a short test cycle to check for leaks at the vent area

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This upper draw bar is a door-latch linkage piece used in dishwashers. It connects the handle/actuator to the latch mechanism so the door closes securely and the door switch engages, allowing the cycle to start reliably.

• Links the door handle/actuator to the latch for positive closure
• Helps ensure the door switch is engaged so the unit will run
• Restores proper latch alignment and handle feel
• Common symptoms: door won't latch or pops open, dishwasher won't start, must push/hold door to run, loose or floppy handle

• Disconnect power at the breaker; turn off water supply if working near the inlet
• Open the door and remove inner-door screws to access the latch linkage
• Note bar orientation; transfer any clips/bushings and reuse existing hardware
• Reassemble and check latch engagement before running a cycle

Almond. Size: 13 oz. can. Acrylic appliance paint.

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

This tub wheel mount secures the rack support roller to the dishwasher tub wall so racks roll smoothly. Replace a cracked or loose mount to restore smooth rack movement and prevent binding or sagging during loading and unloading.

• Secures the tub roller/wheel to the dishwasher's inner tub wall
• Provides a stable point so the rack glides smoothly on its track
• Helps keep the rack level and properly aligned
• Common symptoms: rack hard to slide, tilts or drops, scraping/grinding when moving the rack

• Disconnect power and water supply before servicing
• Pull the rack forward to access the mount on the tub sidewall
• Remove the retaining fastener or release locking tabs, then install the new mount in the same orientation
• Ensure the wheel engages the track and test rack travel for smooth operation

Color: Almond

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning