Kenmore Range 665.75002103 (66575002103, 665 75002103) Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

When bake was set, the stove would function normally, it would show pre-heating then get up to temperature and beep twice like normal when it reached the set temperature. Shortly after it would start beeping and scroll “ fault detected, press start to try again” across the display. Pressing start did not resolve, the message would continue to post and the pizza inside was burnt. We noticed the broil element was glowing. This model stove does use the broil element for backing but it... Read more

Took the stove apart*, saw where the mouse had made a nest. It was kind of like a hotel room after a rock star had used it. It was nasty, is what I'm saying. I removed the insulation, which immediately went into a garbage bag and was placed outside, whereupon I took off and nuked the site from orbit. It was the only way to be sure (actually it was disposed of in the proper manner, no nukes were detonated in the course of this repair). Anyway, I ordered the insulation from this site, which was... Read more

I bought an( as is) range (Maytag) form a dealer. I assumed that it would have racks, however, it came without. I tried to find some racks that would fit but none available. So I decided to order from Appliance Pros and received the right racks two days after I ordered. Very Happy Camper, Read more

I have tried to remove the burner assemblies by removing the torx screws but they were badly rusted, and unfortunately they all were broken during removal. I just discarded the ruined orifices and assembled the new orifices and burner assembly. Read more

Replaced switch with back cover off and power plug pulled. The replacement switch was the same as old, was easy to pull off wires and push on new one. Also replaced torn door gasket with new one and was a exact replacement both only took less than a hour. Read more

Replaced It With New One Read more

Touch up paint Read more

• Element will not heat
• Won't start
• Gas igniter glows, but will not light

Replaced ignitor. Read more

I ordered a new socket and replaced the socket and now we have a light in the oven. The project took about 10 minutes and was easy done. Read more

• Door won't close

Replaced it with new rear guide. Took less than 5 minutes. Also the item came a lot quicker than I expected. Read more

I did a search online for inner door glass replacement pieces and came across a youtube video made by appliance parts pros. After watching the video, I was certain that this was a repair I could do myself. I ordered the glass and it arrived the next afternoon. That evening, I brought the video up on my computer, gathered a screwdriver, some gloves and a towel to lay the door on when I put it on the table. I watched the video as I did the repair, starting, stopping and backing up as needed. ... Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

Replaced old igniter. also purchased new screws for burner and igniter assembly since old screws were corroded from spilled food/fluids etc over the years. made the installation much easier. If you need to replace a worn igniter, do yourself a favor and go to hardware store and get matching replacement screws or buy new with igniter. Now my front right burner lights every time with just a click or two. Very pleased. Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

• Won't start

I purchased a new igniter for the bake assembly and found that it, unfortunately, did not resolve my problem. I measured the resistance of the different points on the gas valve and it was reading within spec so I then purchased this spark module and it did the trick. My gas range is a Kitchenaid kgsk901sss02. I had a LOT of trouble finding where the spark module is located, and eventually found a schematic that shows it's location behind the front control panel of the oven. Upon taking the... Read more