Kenmore Range 790.92903010 (79092903010, 790 92903010) Parts

The Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for controlling the temperature and operation of the warming drawer or zone feature.

Causes of a bad Switch can include electrical malfunctions or short circuits, mechanical wear from repeated use, and exposure to moisture or debris.

Symptoms of a bad Switch include:

• Inability to activate or control the warming drawer or zone
• Erratic temperature fluctuations
• Overheating or failure to heat the warming area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This radiant surface element restores heat to one burner zone on a smooth-top electric range. Replace a burned-out element to bring back responsive, even heating for boiling, simmering, and everyday cooking. What it does:

• Generates radiant heat beneath the glass cooktop for a single cooking zone
• Helps maintain steady temperatures and even heat distribution
• Common failure symptoms: burner won't heat, heats intermittently, or heats unevenly
• Often tests open (no continuity) when failed

• One surface heating element

• Disconnect power before servicing; this is a high-voltage component
• Lift/prop the cooktop and remove mounting screws/clips
• Note wire positions; transfer any brackets/clips from the old element and secure connections firmly
• Center the element under the glass and ensure nothing contacts the element before reassembly

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This oven rack provides a sturdy, level surface for cookware inside your range or wall oven. Replace a bent, rusted, or missing rack to restore safe support and smooth, reliable placement at the proper cooking height.

• Slides into the oven's side rails to hold pans at the desired level
• Supports bakeware evenly and maintains proper clearance for airflow
• Replace when the rack is warped, corroded, flaking, or difficult to slide
• Common symptoms include wobbling, not sitting level, or a missing safety stop

• Allow the oven to cool completely; wear gloves to protect from sharp edges
• Insert the rack with the stop end toward the rear; engage both side rails evenly
• Push in until the rear stops seat; the rack slides freely and sits level
• To remove, pull to the stop, lift the front slightly, then pull straight out

Restore dependable oven-light operation. This door-activated switch turns the oven's interior light on when the door opens and off when it closes, letting you check food at a glance and preventing the light from staying on unnecessarily. What it does:

• Detects door position to control the oven cavity light on/off
• Worn or stuck contacts can make the light stay on with the door closed
• Failed switch can prevent the light from turning on when the door opens
• Intermittent or flickering light may indicate a failing switch

• 1 switch

• Disconnect power to the appliance before servicing
• Access the switch (typically mounted in the front frame near the door opening)
• Move wires to the new switch one at a time to maintain correct placement
• Reinstall, then test door/light operation before final reassembly

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

This is the graphic control panel overlay for the oven/range user interface. It restores legible labels and a clean appearance for touchpad buttons, helping you see and select functions accurately when the original film is worn, bubbled, or damaged. What it does

• Adheres to the control panel/touchpad to provide printed button labels and icons
• Protects the underlying keypad from spills and cleaning wear
• Helps resolve faded, peeling, or unreadable control markings
• Can improve button feel and responsiveness when the old overlay is lifting
• Restores a finished, factory look to the control panel

• One control panel graphic overlay

• Disconnect power to the appliance before starting
• Clean and dry the control panel surface thoroughly; remove all adhesive residue
• Align carefully before applying—once set, adhesive may not reposition cleanly
• Press firmly and evenly to ensure full adhesion and avoid bubbles

This replacement oven door glass panel restores safety and visibility to your range or wall oven. Replace cracked or shattered glass to maintain the door's insulating barrier and a clear view of your cooking without replacing the entire door. What it does:

• Serves as one pane of the oven door window for viewing the oven cavity
• Helps maintain proper door integrity and heat containment when used with the other panes
• Replace if the original glass is cracked, chipped, shattered, or missing
• Can resolve cloudiness or staining isolated to a damaged pane

• One glass panel

• Disconnect power or turn off gas and allow the appliance to cool completely
• Wear cut-resistant gloves and eye protection; handle the new glass by the edges
• Remove the door and disassemble the door stack; retain and reuse existing trim and fasteners
• Clean out all glass fragments before reassembly and avoid overtightening hardware

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This replacement fan motor spins the appliance's fan to move air for cooling and circulation during operation. Replacing a worn motor restores proper airflow, helps protect internal components from heat, and can reduce noise from failing bearings.

• Drives the fan to move air through the appliance as designed
• Common fix for a fan that won't run or turns slowly
• Can help prevent overheating, hot control panel, or thermal shutdowns

• Disconnect power at the breaker or unplug the appliance; allow hot surfaces to cool
• Access point varies by model; remove panels to reach the fan motor
• Note wire positions; transfer the fan blade and any mounting hardware from the original motor if required
• Restore power and test

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

Size: 8-32t x 0.500 inch. Color: Black.

This radiant surface element restores heat to a glass-ceramic cooktop burner. Replace a failed element to bring back even, reliable heating and responsive temperature control for everyday boiling, simmering, and cooking. What it does:

• Provides radiant heat to a designated cooking zone beneath the glass cooktop
• Common symptoms: surface burner won't heat, heats unevenly, or cuts out intermittently
• Visible signs can include burned or cracked element traces or damaged terminals

• 1 radiant surface element

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift or remove the glass top to access the element
• Photograph wiring and transfer leads one at a time to the new element to maintain correct connections
• Support the element and brackets during reassembly and avoid touching the element surface with bare hands

Restore a safe, finished oven door with this replacement outer glass panel. It replaces a cracked or shattered front window, protecting the door assembly and letting you see your food without exposing insulation or sharp edges. What it does:

• Forms the front/outer pane of the oven door window
• Protects door insulation and inner glass from damage
• Helps contain heat within the oven when intact
• Common symptoms: visible cracks, shattered or missing pane, loose or rattling glass

• 1 outer oven door glass panel

• Disconnect power and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; glass edges can be sharp
• Removing the door from the hinges makes service easier; support the door to prevent damage
• Transfer any trim/brackets/nameplate from the old pane and reuse existing hardware as required

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly