Kenmore Range 790.94212409 (79094212409, 790 94212409) Parts

The Oven Seal is an OEM replacement part for Frigidaire ovens. This seal is installed around the oven door to create a tight barrier, preventing heat from escaping during operation. By maintaining the internal temperature, the seal ensures efficient cooking and baking while reducing energy consumption.

Over time, the oven seal can wear out or become damaged due to exposure to high temperatures, frequent use, or accidental mishandling. A compromised seal can lead to heat loss, uneven cooking, or longer preheating times.

Symptoms of a bad oven seal include:

• Heat escaping from the oven door
• Longer cooking times or unevenly cooked food
• The oven taking longer to preheat
• Visible cracks, tears, or flattening of the seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Control Board Overlay is an OEM part for Frigidaire ranges. This part provides the buttons and display that control the range's functions. The overlay covers and protects the control board, ensuring that the buttons and display remain intact and operational.

Causes of a bad control board overlay can include wear and tear from regular use, exposure to heat and moisture, or damage from accidental impacts. 

Symptoms of a bad control board overlay include:

• Buttons that are unresponsive or hard to press
• Fading or peeling of the overlay graphics
• Inaccurate or malfunctioning display
• Visible damage or cracks on the overlay

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Leveling Leg Assembly is an OEM part for Frigidaire ranges. This part provides stability by allowing users to adjust the height of the range, ensuring it is level and balanced on the floor.  

Causes of a bad leveling leg assembly can include wear from frequent adjustments, damage due to heavy loads, or breakage from accidental impacts.  

Symptoms of a bad leveling leg assembly include:

• The range being uneven or wobbling
• Difficulty in leveling the range using the legs
• Noise or movement when the range is in use
• Doors not aligning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Switch Rocker is an OEM part for Frigidaire ranges. This switch is used to control various functions of the range, such as turning on heating elements or activating specific cooking modes. It provides a reliable and straightforward interface for managing the range's features.

You should replace the range switch rocker if it becomes faulty. Causes of a bad switch rocker can include wear and tear from frequent use, exposure to high temperatures, electrical malfunctions, or physical damage from impacts or mishandling. A defective switch rocker can result in unresponsive controls, making it challenging to operate the range effectively.

Symptoms of a bad Range Switch Rocker include:

• The switch not responding when pressed
• Inconsistent or flickering performance of the heating elements
• Physical damage or looseness in the switch
• Intermittent operation or complete failure to activate the desired function

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This burner box is the structural pan beneath the cooktop that supports the surface burner components and shields internal parts from heat and spills. Replacing a damaged box restores proper burner alignment and a stable, secure cooking surface.

• Provides a rigid housing under the cooktop for burner heads, igniters, and related hardware
• Helps contain spills and protect wiring and insulation from heat exposure
• Keeps burners aligned so they sit level and openings match the main top
• Common failure signs: rust-through, cracks, or warping; stripped/broken mounting points; burners wobble or won't secure properly

• Disconnect power and shut off the gas supply before servicing.
• Remove the main top; document locations and transfer burners, igniters, grommets, and brackets to the new box.
• Handle sheet-metal edges carefully; wear cut-resistant gloves.
• After reassembly, restore gas and power, verify ignition, and leak-test any disturbed gas connections.

The Vent Trim is an OEM part for Frigidaire ranges. This part frames and supports the oven's ventilation system, ensuring proper heat dispersal and maintaining the aesthetic integration of the range within the kitchen setup.  

Common causes for vent trim issues include physical impacts during cleaning or use, thermal deformation from continuous exposure to high temperatures, and general wear and tear over time.  

Symptoms of failing Vent Trim include:

• Loose or ill-fitting trim that may not stay in place
• Visible damage such as cracks or warping due to heat exposure
• Increased heat retention or abnormal heat outside the oven
• Aesthetic discrepancies that impact the overall look of the kitchen

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Anti-Tip Bracket Kit is an OEM part for Frigidaire ranges and ovens. This part secures the appliance to the floor or wall, preventing it from tipping over when the oven door is opened or when heavy cookware is placed on an open door or extended rack. The kit typically includes a metal bracket, screws, and installation instructions.

Over time, or during instances of moving or remodeling, the anti-tip bracket may become dislodged or may not be reinstalled correctly, which can compromise the safety of the appliance. 

Symptoms of a missing or improperly installed Anti-Tip Bracket include:

• The range or oven tilts forward when pressure is applied to an open door
• The appliance moves more easily than expected when nudged or cleaned
• Visible absence of a bracket at the lower back portion or floor area behind the appliance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This Door Trim Kit restores the finished look and proper fit around the door. It replaces damaged or missing trim that frames the door/panel, helping secure outer components and refresh the appliance's appearance.

• Provides a clean, finished edge around the door perimeter
• Helps retain/position the outer glass or panel on applicable designs
• Replaces cracked, warped, loose, or missing trim that may rattle or leave gaps
• Common symptoms: visible damage, looseness, gaps, or cosmetic wear around the door

• Disconnect power at the breaker or unplug the appliance before servicing
• Protect the work surface; wear cut-resistant gloves and handle glass carefully
• Note orientation and fastener locations; transfer any reusable clips/screws from the original assembly
• After reassembly, confirm smooth door operation and proper alignment/seal

This terminal block kit restores a secure, heat-resistant connection point for your appliance's incoming power. Replacing a damaged block helps prevent intermittent power loss and further heat damage from loose or burnt terminals.

• Provides an insulated junction for incoming power leads
• Restores a tight, reliable connection between supply wires and internal wiring
• Helps resolve no power, intermittent power, or visible heat damage at the terminal area
• Replaces cracked, melted, or burned blocks to protect wiring and performance

• Disconnect power at the breaker and verify no voltage is present before servicing
• Label/photograph existing wiring; move one conductor at a time to the new block and tighten terminals securely
• Inspect the cord and wire ends; replace any burnt, brittle, or damaged conductors or lugs before reassembly
• Reinstall covers/strain relief as applicable and verify connections are secure before restoring power

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

Size: 3/4 inch od x 1/4 inch id.

The Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for controlling the temperature and operation of the warming drawer or zone feature.

Causes of a bad Switch can include electrical malfunctions or short circuits, mechanical wear from repeated use, and exposure to moisture or debris.

Symptoms of a bad Switch include:

• Inability to activate or control the warming drawer or zone
• Erratic temperature fluctuations
• Overheating or failure to heat the warming area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

This electronic oven control board (clock/timer) is the brain of your range/oven, regulating temperature, powering the bake/broil circuits, and managing the display and keypad. Replacing it restores proper heating and responsive controls.

• Governs bake and broil circuits and maintains set temperature using oven sensor feedback
• Displays time/temperature and responds to keypad inputs
• Common failure signs: oven won't heat or start, erratic/inaccurate temps, dead or unresponsive display, repeated beeps or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board by the edges and use anti-static precautions
• Photograph/label connectors and transfer wires one at a time to the new board
• Transfer the existing keypad overlay and any brackets as needed, reinstall panel, restore power, and test bake/broil