Kenmore Refrigerator 795.58814900 (79558814900, 795 58814900) Parts

Refrigerator not cooling or freezing properly? The evaporator assembly absorbs heat to cool your fridge. Moderate DIY repair with basic tools required.

Water pooling in your refrigerator? A cracked or clogged drain tube assembly causes leaks and ice buildup. Direct replacement part for proper drainage.

Refrigerator and freezer stopped cooling but lights work? This compressor set assembly restores cooling when the motor fails. Advanced DIY repair.

Covers and protects the freezer fan compartment on your side-by-side refrigerator. Replace if cracked, broken, or missing. Mounts with screws.

This is a rear handle end cap that attaches to the back side of a refrigerator door handle. It provides a finished appearance and secures the handle assembly to the door. Replace this cap if it is cracked, broken, or missing, which can cause the handle to feel loose or look incomplete.

This noise damper reduces vibration and rattling sounds from refrigerant lines in your refrigerator. It cushions the copper tubing against the cabinet to prevent metal-on-metal contact that creates annoying noises. Install this damper if your refrigerator makes clicking, rattling, or vibrating sounds, especially when the compressor cycles on and off.

90-degree elbow connector for 1/4" refrigerator water lines. Replaces cracked, leaking, or broken tube fittings between filter and dispenser.

Rail guide assembly mounts inside the refrigerator to support and guide crisper or snack drawers. Replace cracked, broken, or worn rails causing binding.

This is a complete refrigerator ice maker assembly that automatically forms, freezes, and ejects ice cubes into the bin. It restores consistent ice production when the original ice maker stops cycling or no longer makes ice. What it does

• Freezes water in its mold, then harvests and ejects cubes into the ice bucket each cycle
• Controls fill and harvest timing and signals the water inlet valve during the fill portion of the cycle
• Stops ice production when the bin is full via its shutoff mechanism
• Typical failure symptoms: no ice, intermittent/low ice output, or cubes not ejecting

• 1 ice maker assembly

• Disconnect power and turn off the household water supply before servicing
• Remove the ice bin; loosen mounting screws, disconnect the wire harness, and swap in the new assembly in the same position
• Inspect and clear the fill tube of any ice blockage before reconnecting
• Restore power and water; allow the unit to reach operating temperature and begin cycling

This is the water injector tube for select refrigerators. It routes water from the supply system into the appropriate internal channel, helping ensure proper flow to the ice maker or dispenser and preventing leaks at the connection point.

• Directs water from the valve/supply line into the refrigerator's internal water path
• Helps restore proper ice maker/dispenser filling
• Common symptoms: leaking at the rear/under the unit, poor or no ice production, slow or no dispenser flow

• Unplug the refrigerator and shut off the water supply before service
• Have a towel ready to catch residual water from the line
• Note tube routing and connection points before removal; push-to-connect fittings may be present
• After installation, turn water on and check all joints for leaks

This sensor cover protects and secures the appliance sensor assembly to help maintain accurate sensor positioning and guard the sensor from damage, dust, and moisture that can interfere with normal operation. What it does:

• Shields the sensor housing from physical damage, dust and moisture.
• Keeps the sensor properly positioned so it can read conditions reliably.
• Can prevent intermittent sensor faults and related error codes when damaged.
• Helps avoid false readings that can cause incorrect cycles or behavior.

• Disconnect power to the appliance before starting any work to avoid shock or injury.
• Handle nearby wiring and sensor components carefully; avoid touching circuit contacts.
• Verify the cover seats flush and secures to the sensor housing; do not force or deform plastic tabs.
• If any sensor or wiring was disturbed during installation, recheck connections and test operation before regular use.

Plastic door bin that mounts inside your refrigerator door to organize bottles, condiments, and small items. Replace cracked, broken, or missing bins.

Insulated air duct assembly routes cold air from freezer to fresh food compartment. Replace if cracked, broken, or insulation is damaged or missing.

A replacement tempered glass shelf that provides a sturdy, easy-to-clean surface for organizing food and containers in your refrigerator. Restores usable shelf space and helps keep items level. What it does:

• Replaces a cracked, chipped or missing refrigerator shelf
• Provides a stable surface for storing food, bowls and containers
• Resists spills and is simple to wipe clean
• Helps maintain proper organization and airflow on the shelf level

• Remove all food and items from the shelf area before installing
• Slide shelf into the support rails until it seats evenly on both sides
• Handle with care — tempered glass can break if dropped or struck
• If shelf supports or rails are damaged, replace or secure them before use