Kenmore Refrigerator 795.79772902 (79579772902, 795 79772902) Parts

• Leaking
• Not dispensing water

I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more

• Leaking

Removed the old line and replaced with the new. This is the sixth time I've replaced the line. Yes you read that right, the sixth time. Lines fail about every 6-8 months so I can change one out now in about 10-15 minutes. Bought the refrigerator in Feb '09 and the line first failed in March 2012. Since then I've had failures in as little as 4 months to as much as 9 months. Frustrating to say the least, but I'm a whiz at changing out the line :-) Read more

• Ice maker not making ice

Replaced ice maker. The hardest part was getting to the power plug behind the ice maker to remove and replace it. Once the new ice maker was installed it started making ice again. Read more

I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more

• Fridge too cold
• Fridge too warm

I replaced the evaporator sensor. Your company sent me the exact sensor I needed at a great price. No other company was able to help. No call was needed. Your website was great. Read more

• Doesn't shut off
• Fridge too warm
• Noisy

Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more

Ordered new tube part AJR56656503 for Lg LFX25978ST/01 watched a lot of videos but none showed how to remove the door tube end from its connection so I just cut and spliced the new tube to the old under the cover for the door hinge area after feeding it from the back of frig to that area. It was easy till I tried to remove the line end from ice maker area. Read more

Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more

Replaced defrost sensor in freezer compartment, if you are handy this is a do it yourself job. The cover in the freezer section just pops out not tools needed. You will need a few small zip ties and some cutters to remove the old zip ties. Take a picture were the old sensor was before removing and reinstall in the same place. I used a meter to check continuity of the defrost element and found the element to be ok. I was quoted $85 to have someone come to the house just to check the unit and... Read more

• Leaking

First I replaced the filter thinking it was the problem, but that was not the case. Next was replace water supply valve at the back of the refrigerator. It was very easy. The only thing that was in question was how to get the refrigerator side line off of the existing valve. There is a plastic slide clip that you remove and pull the line out and press the line back into the port it came out of. It was a very simple project and took about 20 minutes. Read more

It was just a broken bin. We replaced it. Read more

Ordered parts, removed top tray in freezer, popped the back inside freezer panel out removed and replaced fan, dampers and fan housing. Took about 15 minutes. Read more

Appliance Parts was the only one of three companies that did it right. When the glass in our rather new LG fridge broke, I called the number listed in the manual for replacement parts and was put through to their "authorized distributor" for our area. The authorized distributor sent us the wrong part (entirely different dimensions) with a packing slip identifying the right part number. Because this is not a review of that company (which would be horrible, I won't share the gruesome details of... Read more

The old filter head was broken at the supply line side connector fell out. The clicking noise eventually caused the fridge to warm up and stop cooling. The clicking was the overload relay tripping. The Start solenoid on the compressor was an Embarco TSD part 513604044. APP does not have that part nor does any else found a similar one on ebay but I ordered the PTC assembly 6749C-0014E. I removed the overload relay and capacitor from the TSD used two pieces of wire and connectors to create the... Read more

I found the condensing fan motor would not turn with power applied. I also found a drain tube cracked and breaking. I had to use a snub nose screwdriver to remove and replace condensing fan motor. The power wires were simply a snap on. The new drain tube just slipped on. Thanks for the speedy delivery! Stephanie Hobbs Read more