Kenmore Washer Dryer Combo 970.-C90862-00 (970-C90862-00, 970 -C90862-00) Parts

The Dryer Timer Knob is an OEM part for Frigidaire dryers. It is responsible for allowing users to set the drying time and cycle selection by turning the timer shaft. The knob securely attaches to the timer and provides an easy way to control dryer settings.

Over time, the timer knob can become damaged due to repeated use, excessive force when turning, or wear on the internal connection points. If the knob becomes stripped, cracked, or no longer stays in place, it may need to be replaced.

Symptoms of a bad timer knob include:

• The knob spins freely without adjusting the timer
• Cracks or breaks in the knob
• Difficulty selecting or changing dryer settings
• The knob does not stay attached to the timer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Start Switch is an OEM replacement part for Frigidaire dryers. This part initiates the dryer's cycle once the user selects the desired settings. By pressing the start switch, the motor activates, and the drying process begins, ensuring clothes are dried according to the selected specifications.

Symptoms of a bad Start Switch include:

• The dryer not starting when the switch is pressed
• Intermittent starting issues, where the dryer sometimes starts and sometimes doesn’t
• The need to hold the switch in place to keep the dryer running
• Unusual noises when the switch is pressed

Causes for a malfunctioning Start Switch can include electrical issues, such as faulty wiring or connections, wear and tear from frequent use, or internal failures within the switch mechanism that prevent it from signaling the motor to start.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryers.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Ball is an OEM part for Frigidaire dryers. This part helps the drum to rotate smoothly and evenly. It provides a stable and low-friction contact point, allowing the drum to turn efficiently during drying cycles. This is a drum-bearing ball only. For a complete drum bearing and shaft kit order 5303281153.

Causes of a bad ball can include regular wear and tear, friction from continuous drum rotation, or physical damage. 

Symptoms of a bad dryer ball include:

• Squeaking or grinding noises during operation
• The drum not rotating smoothly or becoming unbalanced
• Increased friction leading to higher energy consumption
• Visible wear or damage to the ball

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles. 

Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines. 

Symptoms of a faulty ignitor can include:

• The dryer fails to start or stop heating intermittently   
• Cycles taking overly long to complete or feel uneven
• Excessive service calls relating to "no heat" troubles  
• Risk of uncombusted gas pooling in dryer if ignition falters

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.

Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.

Symptoms that may indicate the need for a replacement leveling leg:

• Uneven or unstable washing machine
• Excessive shaking or vibration during spin cycles
• Difficulty in leveling the washer during installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

The Capacitor is an OEM part for Frigidaire washing machines. This part stores and releases electrical energy to start and maintain the operation of the washer's motor, ensuring it runs smoothly during wash and spin cycles.

Causes of a bad capacitor can include electrical surges, general wear and tear over time, or exposure to high temperatures and moisture.  

Symptoms of a bad capacitor include:

• The washer not starting or having difficulty starting
• The motor running intermittently or not running at all
• Unusual humming or buzzing noises from the washer
• The washer stopping mid-cycle or not completing cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

For a complete drum bearing and shaft kit order 5303281153.

The Drive Motor is an OEM part for Frigidaire washing machines. This component is essential for powering the washing machine's drum, enabling it to agitate and spin during the wash and rinse cycles. It ensures that clothes are thoroughly cleaned and properly spun dry.

Common causes of a bad drive motor include wear and tear from frequent use, overheating due to heavy loads, electrical issues such as power surges, and physical damage from impact or mishandling.

Symptoms of a bad drive motor include:

• The washing machine not spinning or agitating
• Loud, unusual noises during operation
• The washer not starting or stopping mid-cycle
• Burning smell or visible signs of motor overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Includes motor, motor pulley and housing. Motor pulley no longer available separate

This white door handle replaces a cracked, loose, or missing handle. It restores a secure grip so the door opens and closes properly and refreshes the unit's appearance with a clean, factory-color finish.

• Provides the handhold used to open and close the door
• Common fix for a broken, cracked, or missing handle
• Helps when the handle feels loose, flexes, or falls off
• Restores the door's look with a matching white finish

• Disconnect power before servicing.
• Support the door while removing/installing the handle to prevent stress on hinges or glass.
• Remove the original mounting screws, align the new handle, and reinstall using existing hardware.
• Do not overtighten screws to avoid cracking the handle or door panel.

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks