Lg Washer Dryer Combo 29002 Parts

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

Balancer assembly mounts to the washer basket to counterbalance loads during spin. Replace if cracked, damaged, or causing excessive vibration.

Replace a cracked or clogged washer nozzle assembly to restore proper water flow and prevent poor cleaning performance. Moderate DIY repair.

Genuine hardware washer that distributes fastener load at assembly joints. Replace if worn, cracked, or causing loose connections. Confirm fit with your model.

This rubber fill hose connects the household hot water supply valve to the washing machine's water inlet valve. It delivers hot water into the wash tub during the fill cycle. Replace this hose if it is cracked, leaking, bulging, or showing signs of deterioration to prevent water damage.

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

This is the internal fill hose that connects the water inlet valve to the wash tub inside the washing machine, delivering cold water during the fill cycle. It is a rubber or reinforced hose with fittings on each end. Replace this hose if you notice leaking underneath or behind the washer, or if the machine is not filling properly with water.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

Molded trim piece that shields and supports the washer guide track assembly. Replace if cracked, broken, or missing to maintain smooth alignment.

Small metal washer used in washer internal mounting assemblies. Provides proper spacing between components and secures fasteners. Replace if worn or missing.

Suppresses electrical interference on your washer's AC power line to protect control boards. Replace if washer won't power on, stops mid-cycle, or controls malfunction. Verify fit by model number.

Replacement mounting bracket holder that secures internal washer components. Needed when your original bracket is cracked, broken, or missing.

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

Tapping screw secures washer panels, brackets, and trim in place. Replace stripped, rusted, or missing screws to restore proper fit and stability.

Fix excessive vibration and loud noises during spin cycles with this washer suspension assembly. Stabilizes the drum and reduces movement during operation.