Need Help?
Call
Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.
What it does
What’s included One shipping bolt assembly (sold individually).
Install notes
Usage tip After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.
AppliancePartsPros had the needed items in stock, and I had them within 48 hours of the parts being shipped. Read more
Seals the gap between inner and outer tubs to prevent water leaks. Replace if you notice water stains or pooling beneath your washer. Verify fit.
An online search for LG washing machine parts came up with a repair video from Appliance Parts Pros. I watched the video. It was very well done, very detailed, and took you step by step through the entire process to replace the tub bearings and the spider, from start to finish. After watching the video, I realized this repair was well within my abilities. No specialized tools were needed. I ordered the parts from Appliance Parts Pros, and all items were in stock and delivered within a couple... Read more
The Float Assembly is an OEM part for LG washing machines. This part monitors and controls the water level within the appliance. It's a safety feature that prevents water overflow and potential flooding, contributing to the efficient operation of the washing machine by maintaining the correct water level for each cycle.
Causes of a bad Float Assembly can vary from simple blockages that prevent the float from moving freely to electrical faults within the switch mechanism.
Symptoms of a bad Float Assembly include:
This OEM LG part is also compatible with some Kenmore models.
The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more
The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.
Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.
Symptoms of a bad vent hose include:
This OEM LG part is also compatible with Sears/Kenmore.
Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more
Seals the outer tub to prevent leaks during wash and spin cycles. Replace if you notice water leaking or when replacing tub bearings. Confirm fit.
The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.
Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.
Symptoms of a bad clamp include:
This OEM LG part is also compatible with Sears/Kenmore models.
If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more
Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.
Remplace todos los baleros y el sello de la tina de mi lavadora lg tromm wm1814cw pero al tratar de despegar la tina le di mal con el martillo a ese tornillo y lo doble un poco y ya no lo quise poner asi por eso lo pedí y al llegar mi pedido ya estaba todo listo para solo poner ese tornillo y empezar a lavar Read more
Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.
Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm! Read more
Directs water from inlet valve to detergent dispenser in LG washers. Replace if hose is cracked, leaking, won't stay attached, or damaged from wear.
I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more
The Rotor Position Sensor is an OEM part for LG washing machines. This sensor monitors the speed and direction that the washing machine tub is spinning. It ensures the tub rotates properly in both clockwise and counterclockwise motions during cycles.
Causes of a bad rotor position sensor can include wear and tear from extended use agitating heavy loads, breakage from impact or moisture damage, or compromised wiring over time.
Symptoms of a bad rotor position sensor include:
I was having trouble with my Kenmore Front Load washer. It wouldn't finish the wash cycle...it kept displaying an LE Error code. After I went to Google to help diagnose the problem, which was a bad RPS Sensor, I ordered the part from AppliancePartsPros.com. It literally took about 15-20 mins and with the help of my son-in-law, my washing machine was fixed!! It was going to cost me $85.00 for the Sears repairman to walk in my door, not including parts and labor, and I only paid $27.00... Read more
Seals washer door to prevent leaks during cycles. Replace if torn, cracked, or leaking. Verify fit with your model number before ordering.
Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.
Took top off and did a line at a time Read more
Rear tub support spider for washers. Mounts behind the outer tub to brace against vibration during spin cycles. Replace if cracked or broken.
Bleach dispenser funnel for LG front load washers. Installs in detergent drawer to safely dispense bleach. Replace if cracked, broken, or missing.
The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more
This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.
Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.
I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.