Lg Washer WM2020CW Parts

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

Fixes washer that won't spin or makes grinding noises during spin cycle. This rotor assembly mounts on the motor and works with the stator to turn the drum.

Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.

Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.

This rubber fill hose connects the household hot water supply valve to the washing machine's water inlet valve. It delivers hot water into the wash tub during the fill cycle. Replace this hose if it is cracked, leaking, bulging, or showing signs of deterioration to prevent water damage.

Joins two internal water lines in your washer. Replace this coupler if cracked, worn, or leaking to restore a secure connection during fill and wash cycles.

This kit includes the bushing components that fit into the door hinge assembly on a front-load washer. The bushings reduce friction and allow the door to pivot smoothly when opening and closing. Replace this kit if the washer door feels loose, sags, makes grinding or squeaking noises, or no longer aligns properly with the door latch.

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out during the drain cycle. Replace it to resolve leaks or drain errors caused by cracks, splits, or internal blockages.

• Routes wash water from the outer tub to the drain pump
• Flexible bellows section helps prevent kinking and accommodates tub movement
• Failure signs: water leaking under the washer, slow/no draining, drain-related error codes, or visible cracks/soft spots
• Often needed after clamp corrosion, physical damage, or age-related deterioration

• Unplug the washer and turn off water supply; drain any remaining water from the tub/hoses
• Access location varies by model; remove panels as needed to reach the hose and clamps
• Use pliers to release spring clamps; note routing and clamp orientation before removal
• Seat the hose fully on fittings, secure clamps, and test with a short drain/rinse cycle to check for leaks

Washer won't spin or shows LE error? A failed stator loses the magnetic field needed to rotate the drum. Moderately difficult repair with rotor removal.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

These non-skid pads attach to the bottom of the washer's leveling legs to prevent the machine from sliding or walking across the floor during operation. They are made of durable rubber or similar grip material. Replace them if your washer vibrates excessively, moves out of position during spin cycles, or if the existing pads are worn, cracked, or missing.

This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:

• Replaces a worn, cracked, or missing control knob to regain safe, predictable control
• Engages the shaft and detents so settings stay put during use
• Helps eliminate slipping or difficulty turning the control
• Matches original fit and function for direct replacement

• One knob assembly as shown

• Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
• Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
• Wear work gloves to protect hands from sharp edges during access

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.