Lg Washer WM3475HVA Parts

Includes sensor probe

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

Replace a broken, rusted, or missing leveling leg assembly. Installs at the base to stabilize your washer, reduce vibration, and adjust height.

Secures the drum during washer transport or relocation. Replace missing, stripped, or damaged shipping bolts to prevent internal movement and damage while moving.

This rubber fill hose connects the household hot water supply valve to the washing machine's water inlet valve. It delivers hot water into the wash tub during the fill cycle. Replace this hose if it is cracked, leaking, bulging, or showing signs of deterioration to prevent water damage.

Fixes loud banging or clunking during spin cycle caused by loose or broken balance weight. Reduces vibration and stabilizes drum movement. DIY repair.

This inlet hose routes household water into the appliance's fill system, providing a secure, watertight connection. Replacing a worn, cracked, or leaking hose restores proper fill and helps prevent leaks and cycle interruptions.

• Directs incoming water from the supply connection to the appliance's inlet/fill assembly
• Maintains a sealed path to prevent drips and leaks
• Replace if the hose is cracked, swollen, kinked, or fittings are corroded
• Typical symptoms include leaks behind/under the unit, slow or no fill, or a water supply error message

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure
• Note routing and fitting orientation; transfer any seals/clips from the original if required
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, then restore water and check for leaks

This drain hose cap seals and secures the refrigerator defrost drain outlet so meltwater is directed into the drain hose instead of pooling in the cabinet. Replaces a worn or damaged cap to help stop interior leaks and water buildup. What it does:

• Seals the defrost drain outlet to prevent water from spilling into drawers or onto shelves.
• Guides defrost/meltwater into the drain hose and toward the drain pan.
• Helps reduce odors and pests entering through an open drain opening.
• Fits onto the drain outlet to replace cracked, missing, or loose caps.

• Disconnect power before working inside the refrigerator to avoid electrical hazard.
• Remove shelves and drawers as needed to access the drain outlet; clear any visible debris or ice first.
• Press the cap firmly onto the drain outlet/hose until fully seated; avoid excessive force or prying tools.
• After installation, pour a small amount of warm water down the drain to confirm proper flow and seating.

Mounts inside the washer drum to lift and tumble clothes during the wash cycle. Replace if cracked, broken, or missing to restore proper agitation.

Secures hose connections to maintain watertight seals in your washer. Replace if you notice leaks or loose hoses during operation. Verify fit with model number.

Washer won't start or runs intermittently? A faulty wiring harness disrupts power flow between components. This repair restores connections in 20-30 minutes.

Restores proper door tension for smooth opening and closing. Replace if door sags, closes unevenly, or slams. Confirm fit with your washer model number.

Machine screw that fastens brackets, panels, or housings in select washers. Replace when missing, stripped, or damaged to restore secure assembly fit.

If your washer leaks during fill or has low water pressure, this water inlet connector hose restores secure water flow. Direct replacement part.