Samsung Wall Oven JVM-1730DP2CC Parts

• No heat

After dismounting the unit from its wall-hanging bracket, the most tedious part of the repair was removing over a dozen screws holding the cover in place from the top, bottom, and both sides. Fortunately, I had placed the unit on a bench that allowed me to slide the unit allowing access to the screws on the bottom edges of the unit. Always discharge the capacitor before continuing to work on the unit by discharging the capacitor by shorting the contact without the diode to ground. Access to the... Read more

• shuts off after a few seconds

I did some searching on the internet to see if others had the same issue I was having. There were many who had the same problem and everyone of them fixed it by changing out the latch switches, which in my case, were part of the latch body assembly. So I ordered the part from AppliancePartPros and it arrived on Tuesday, 2 business days after I ordered it, which was just as expected. I had also done some research regarding how to replace the latch body assembly and, although I couldn't find... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

I got it in the mail, I opened it, I handed it to my wife....and she installed it. Easy-Peasy! (Being retired is a blast) Read more

I took the machine screws out of the outer panel for the right side only. Then pull the panel back a bit to release the lips from the front of the machine and had immediate access to the internal assembly that housed mounting nut. Order the new parts from AppliancePartsPro.com during the Thanksgiving week. Still received via FedEx in short time due to their same day shipping - which was greatly appreciated and surprising. Most small part places take a while to get the product out the door,... Read more

Ordered a new tray and specified 3-5 day shipping.. The tray arrived the next day on Saturday with no up charge on shipping. Read more

• broken bulb

Unplugged the microwave & took needle nose pliers to gently twist the metal part out of the socket after removing the glass cover for the light. Gently twisted the new bulb into the socket. Read more

Ordered parts from appliance parts pros and downloaded instructions.. Read more

• Won't start

Watched u-tube Read more

Screwdriver Read more

• Tray won't turn

Ordered new from here, it came THE NEXT DAY! Read more

I took the machine screws out of the outer panel for the right side only. Then pull the panel back a bit to release the lips from the front of the machine and had immediate access to the internal assembly that housed mounting nut. Order the new parts from AppliancePartsPro.com during the Thanksgiving week. Still received via FedEx in short time due to their same day shipping - which was greatly appreciated and surprising. Most small part places take a while to get the product out the door,... Read more

Opened up hinged bottom of microwave and saw that the old motor had come loose from its secure position. I decided to replace the old motor with the new one and secured it into place, which was very simple--just a matter of unplugging the old motor's connection; plugging in the new one; securing the motor in place with one screw; closing up the hinged bottom; putting in the new coupler; and checking to see if it works. It did! Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

• broken bulb

Our microwave is mounted over the range, and has dual lights underneath that light up the range. A while back in trying to replace burned out bulbs, one of the bulbs broke and in trying to remove the rest of the bulb from the socket, I accidentally destroyed the socket. We worked fine with the remaining bulb for a year or so, but it finally burned out. Unfortunately all of the replacement bulbs would only last 1-2 days before burning out again in the one socket. When I'd originally destroyed... Read more