Samsung Refrigerator RF28NHEDDSR Parts

I noticed that the bottom of the plastic bucket was cracked even though it was less than two years old. I called Samsung and they wanted to charge me almost $200. Instead, I found the part at appliance parts pros for half that cost. Since I replaced the ice tray bucket assembly, my ice maker is working perfectly! Read more

Replaced fan motor, temperature sensor and defrost thermostat. Note: I had to replace connector on new defrost thermostat. Connector on new part did not fit mating connector in refrigerator.. spliced in old connector for new one. Read more

Replaced broken handle support bracket (part #AP5620448) and cap (part #AP5620751). Used a phillips head screwdriver and allen wrench. Pliers also came in very handy. If replacing cap and support bracket, be sure to install cap before support bracket, otherwise you'll have trouble installing the cap. I ended up not needing to replace the fixer handle (part #AP4372038), but I'll keep it around just in case. Read more

Repair went great thanks for your service Read more

I loosened middle hinge by the 2 screws which holds a power cord that clips together, then slid the hinge flap upward to release from the door. My bottom clip hinge was broken away from spring and the only way to attach a new hinge clip was to carefully separate the hinge flap. This can be done by squeezing the flap to see where the separation seams are. Small narrow screwdrivers along with a spatula will do without damaging the plastic. This allowed for acess to the spring which connects to a... Read more

I ordered the French door housing, the new piece has a solid raised curved part that enters the guide, and a new center hinge. I watched both repair videos shown on appliance parts Pro. It looked pretty simple, so I got my 2 screw drivers and unplugged the refrigerator and started. The hardest part was removing the upper and lower hinges. The video didn’t show how he got them loose, after several minutes of frustration I figured out how to release the hinge. The new parts installed really... Read more

Followed your instruction from your youTube instructions Read more

Replaced broken handle support bracket (part #AP5620448) and cap (part #AP5620751). Used a phillips head screwdriver and allen wrench. Pliers also came in very handy. If replacing cap and support bracket, be sure to install cap before support bracket, otherwise you'll have trouble installing the cap. I ended up not needing to replace the fixer handle (part #AP4372038), but I'll keep it around just in case. Read more

Replaced chute gasket and ice bin. Has worked great so far. Fingers crossed. Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

Using the website, I was able to locate the part and order it Read more

I took all the items out of the refrigerator. Removed the screws that hold the cover over the evaporator motor. Than for three hours used a hair drier to remove ice. The panel was frozen on if you pull on it it will break. Soaked up all the water removed the panel and took the fan blade off. That was difficult because it looks like a regular screw head however, you need to push in that which will cause it to release the blades and than push it onto the new motor. Than replace the panel put the... Read more

• Light not working

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

After discovering that our leaking fridge was caused by a plastic water storage tank I went on the hunt to find a replacement. Sadly there is no replacement available instead you have to purchase the entire filter tank assembly. Since I only needed the tank I carefully took apart the new unit and removed the tank. The biggest hassle is making sure you go slow so you can remove the front of the housing. Then the right side of covers the tank, pump and lines. The lines are the easiest to... Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more