Samsung Washer WF317AASXAA Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

Replaced door lock switch. Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more

• Won't start
• Lid or door will not open
• Lid or door won't close
• Will not agitate

The washing machine would allow you to program it, and all the lights on the control panel would light up, but pressing start did nothing. I tried putting the washer in diagnostic mode, but was unable to do so. The machine was not showing any fault code. I originally thought it was a problem with the 'Start' button and I thought that I'd buy a replacement part from the original seller of the washer. I was told by the 'live help chat person' that the problem was likely in the washer user... Read more

• Leaks water

Noticed large banging in the washing machine when transitioning from low to high speed spin. Also would get a slight smell of burnt rubber. Did an online search and best guess was the spider arm assy was broken. Ordered the spider arm assy, the rear tub seal and the tub seal. Make sure you get blue threadlocker - you'll use it multiple times during the reassembly. The washer is 9 years old and is heavily used. Used the online video on the appliancepartspros.com site to handle the repair. The... Read more

I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

• Door latch failure

I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more

Ordered a new outer door seal and watched their video before replacing. Easy to follow the video and it took me less than 30 min to complete repair. A small amount of diluted dishwashing liquid on the new seal lip makes the install much easier. Read more

The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more

I ordered new door gasket, front and rear clamp for gasket and installed them. Read more

First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes... Read more

Replaced flow meter and control valve Read more

Ordered new dispenser assembly and replaced it. Fixed the problem. Read more