Samsung Washer WW25B6800AW Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

• Leaks water

Noticed large banging in the washing machine when transitioning from low to high speed spin. Also would get a slight smell of burnt rubber. Did an online search and best guess was the spider arm assy was broken. Ordered the spider arm assy, the rear tub seal and the tub seal. Make sure you get blue threadlocker - you'll use it multiple times during the reassembly. The washer is 9 years old and is heavily used. Used the online video on the appliancepartspros.com site to handle the repair. The... Read more

I opened the washer and replaced the pump. To open the washer: 1. Remove the 2 screws that are different from the others in the top back corners of the machine. That will let you remove the top. 2. Remove the soap tray and its holder. The tray comes out if you depress the tab in the back center. Its holder comes out if you remove the two screws in the front. You can leave all the hoses attached. 3. Remove the control panel. It snaps in. Undo the top snaps first. You'll have to reach... Read more

I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more

Followed the excellent videos provided by AppliancePartsPros. Made a multi step repair, if not simple, then extremely less complicated. Loved the way they showed the step by step disassembly as well as the step by step reassembly. Great videos. Got the right parts the first time and very fast delivery. Can’t say enough good things about AppliancePartsPros.com Read more

Removed top panel to reach the hose and sensor. Propped the washer back, reached up to remove bottom hose assembly. Replaced with new hose and new sensor. Put top panel back on. Parts place told me the part was backordered for months and repair would cost at least $80. Got it in three days and fixed it myself. Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

For Samsung Washing clothes machine WA50F9A7DSP/A2 The large (about 1 inch) nut at the bottom of the tub that holds the tub onto the clutch/motor is NOT Appliance Parts Pros 6021-001573, described as NUT-HEXAGON M26 OD44 ZNDC1. This nut has a 24 mm internal diameter. It is marked ZNDC-1 MT26 70H on top of the nut and is left hand or reverse thread. It is slightly too small to thread onto the clutch shaft. THE CORRECT NUT has a 26 mm internal diameter. That is Appliance Parts Pros... Read more

I took it apart and discovered what parts to replace. Called support to verify parts needed and with their help, we ordered everything we needed. Replaced parts and now it's like I have a new machine. Read more

I first called the company and spoke with a gentleman who sent me the part I needed. Very helpful! It was easy to install after watching the video on how to do so. All is good and I'm washing again. Thank you, Barbara Read more

• Won't start

First I checked the breaker and outlet and both were good...then I unplugged the machine, took the top off, and removed the control panel. I check the wiring to see if there were any loose plug ins, etc...This is where I figured the panel was bad (or possibly the power cord) so I ordered both. The parts arrived the next day. (incredibly fast shipping) Since I wasn't expecting them til after the weekend I left everything disassembled and went on a mini vacation for a couple of days. Upon... Read more