Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Circulation Pump by Bosch

Best Seller
Manufacturer Part
4.89 (64)
By: Bosch
Part Number: OEM8479161
Manufacturer Part Number: 00239144

Questions & Answers

For Bosch Circulation Pump (Part Number: OEM8479161)

1 Answer

David,

You will want to access the impeller of the circulation pump and make sure that there is nothing caught in the impeller. If there is like a bread tie or something of that nature that got in there it would cause this type of noise. If this checks ok then the bearings of the motor would be the likely cause of the noise.

Read More...
P.S. for Model Number SHX45M05UC/48

Almost immediately after I start the dishwasher, a buzzing/grinding sound comes from beneath the unit. It finally got so the dishwasher would not wash. I initially thought it was a faulty drain pump, which I have now replaced. The buzzing/grinding continues on start-up and now the flood pan beneath the unit immediately fills with water. When I open the dishwasher door, I can hear the soft sound of the pump (presumably the drain pump). If I empty the flood pan and turn the unit back on, it buzzes/grinds and the flood pan refills with water. Is it the circulation pump?

1 Answer

Hello P.S.,
This sounds like a piece of broken glass is in the sump assembly and is contacting the pump impeller. You will need to access this from inside the unit. Pull out the filters and remove the one screw visible from inside the sump assembly. Use a wet vac to clear the area. This will normally correct the complaint you listed.

Read More...

1 Answer

Hello Frank. Yes, dirty filters and cracks in the tube or spray arms will cause poor cleaning.

Read More...
Etay for Model Number shx45p05uc/64

I have a dishwasher which is not washing well. The upper arm gets water, but not enough to spin and the bottom one spins but barely cleans anything. I took the unit out and ran it without filter in the sump to make sure the sump fills up to the top level, which it does. I also made sure the pump actually turns when the unit runs by visually looking at it when it runs from the back of the unit, (I can see the fins running). I then went on to disconnect the sump assembly and removed the circulation pump (with impeller assembly) from the main sump so I can inspect it. The pump is not seized and I can move the impeller freely with my finger. It does not feel like there are bad bearings or anything holding the motor back from spinning and I did not see any blockages in the intake piping. At this stage I am wondering if I should just order a replacement pump and hope that fixes the issue or if I possibly missed something? Thanks

1 Answer

Hello Etay,
You should not just look for clogs and restrictions but also for any point that can cause a loss of water pressure. This causes the water pressure to be low and a poor wash result. Check the spray arm assemblies for separations and the point where the middle spray arm couples at the rear of the upper rack to the feed tube in the rear of the unit.

Read More...

1 Answer

Caren,

You will want to check the filters in the unit to make sure that they are not dirty. Check to make sure that there is nothing caught in the circulation pump impeller which would cause this issue. Make sure that there is enough water getting into the unit. If all this checks ok then most likely the circulation pump is bad.

Read More...

1 Answer

Lee,

While it does sound like the issue could be the circulation pump, you will want to open the base of the unit and inspect it. It sounds like there may be some damage to other things like the housing since there is white plastic coming out.

Read More...
Tim for Model Number SHY56A06 UC/14 (FD8301-)

My actual Bosch model # is SHY56A06 UC/23 sn FD8508. It seems like the unit is not getting enough water, the pump is noisy, like it is running dry, but some water does fill the tub, just not enough. I took the supply line off and water is full force. Reading stories here, leads me to the water inlet valve, but it is allowing some water in. Is there a way to "test" or inspect the valve to verify it is the issue, or could it be a water pump after the inlet valve? Is that the circulation pump? Thanks

1 Answer

Hello Tim,
If the unit is not filling with a sufficient amount of water, the water pressure to the unit should be checked first, then the water valve 00425458 should be replaced.

Read More...

1 Answer

Corny,

You will want to pull the drain hose and check to make sure that the hose is not clogged. Make sure that the flapper that would be on the pump is not damaged. Check for power to the drain pump and make sure that there is power going to it. If no power then the control module would be the issue and if there is power then the drain pump would be the issue providing no clogs in the hose.

Read More...
Morgan for Model Number SHU53E05UC/14 (FD8502)

I'm trying to buy a circulation pump for our Bosch dishwasher. I had one circulation pump picked out and out of curiosity did a model number cross reference to see if the pump matched my washer model and it said it did not on your website. So I clicked the link to find parts for my model number, found the circulation pump that was recommended by your site, did another check on that page to cross reference that part with my washer and your site said that it was not the correct part. Can I get a confirmed circulation pump # or a direct link to the proper pump for this dishwasher? SHU53E05UC/14 (FD8502) Thanks in advance. Morgan

Robert for Model Number SHX33A05 UC/14 (FD 8211-)

Hi, I have a Bosch Dishwasher. Model #: SHX22A05UC/14. I am trying to trouble shoot what may be wrong with it. The dishwasher made a really loud noise like something was burning out. There was some water left in the bottom of the dishwasher. I was able to drain the dishwasher by bypassing to the empty cycle. The dishwasher does not work at this point. When I turn it on it sounds like it is stuck and does not go on to do anything. Before I spend all kinds of money and time on it I would like to know what you think it is. Please email me back. Regards, Robert

1 Answer

Robert,

If the unit does not fill now and does nothing at all then the issue sounds like it may be in the control board. If the unit fills but nothing else then it sounds like the circulation pump would be faulty.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google