Tonyc June 08, 2020 for Model Number SHP65T55UC/01 I have a Bosch dishwasher SHP65T55UC/01 that was given to me. When I hooked it up and hit start, water began to flow rapidly into the side inlet tank and then overflowed into the bottom basin, triggering an E15 error. I tried turning the water pressure down from the water line to see if slowing down the flow of water would help it not overflow. It stopped overflowing, but instead all the water flowed into the dishwasher, but the circulation pump never kicked on. The water kept flowing until it filled the inside bottom of the dishwasher and began to leak around the door. So I shut off the water supply. Any idea what could be the cause of the problem?
1 Answer Tony, any idea how long the dishwasher was in storage or unused? "E:15 Float switch activated and dishwasher runs continually / can’t be turned off." You will want to check the drain hose and drain pump for operation and drain. check to make sure the float switch 00622036 and float aren't "stuck" in the down position, make sure any water left in the base of the dishwasher is removed and dried completely. Check or consider replacing the fill valve 10023852, it could be "sticky" and remaining open, too long and allowing the tub to overfill.lastly, check the wiring between the float switch and the control board to make sure there are no loose, corroded connections or broken damaged wires. Read More...
Dave A September 27, 2018 for Model Number SHU5312 UC/12 I push the power button , light comes on but it will not start all cycles thanks
1 Answer Dave, This issue would most likely be caused by a faulty control module 00266746 but will also want to check the door switch on the unit. Read More...
J July 12, 2018 for Model Number SHX65PO5UC/60 I have a Bosch Dishwasher model SHX65PO5UC/60. Previously the dishwasher was draining but not spraying water at all. It would slowly come into the bottom, but not spray. I took it apart and replaced the Circulation Pump. Now it drains, Sprays water and then sit and counts down time. From what I have read it could be the control board or the heater. Is there a way to test which one it is, or is it something different?
1 Answer J, You would want to test the heater to make sure that the heater is good by doing a continuity test on it. If the heater checks ok then the control board would be the most likely cause for this issue. Read More...
Jim January 13, 2018 for Model Number Bosch SHU5312UC/U06 Some of the buttons on my Bosch dishwasher no longer work. I need to replace the control panel, but have not found one on line that matches my model number. My number is SHU53112UC/U06. Will control panel 266746, which works for model SHU53112UC/06 also work for my unit?
1 Answer Jim, With the buttons not working then this will be an issue with the control module which is part number 00266746. Read More...
1 Answer Jim, To remove the control module you would need to remove the screws on the inner door panel which will allow you to access the control module to replace it. Read More...
Chris May 05, 2017 for Model Number Bosch SHU43C02 UC/14 I need to remove and replace the control module 647475 (latest PN to replace old control module). I also need to replace one of the four buttons on the panel. Nothing comes up on my internet search so I hope you will be able to help. (video or pictures I have been able to remove the control panel which gives partial exposure to the wires going into the CM but the terminals look like they lock and I cannot see how to release the plastic terminal ends from the old control module. It is also not clear how to keep the rectangular white "buttons" retained in the panel that actuate the push switches on the CM.. How does one get these guys to stay in place without falling out?
1 Answer Chris, The wires will have a tab on them to press in order to take them out and if there is no tab just pull them straight out. The button should clip into place on the panel. Read More...
Charlotte F. April 17, 2017 for Model Number GE dishwasher PDW998ON On the hidden control panel, the up arrow does not light up, but the down arrow will toggle you through the cycles. What would be Needed to correct that situation ?
1 Answer Charlotte, you would need to replace the key pad assembly WD34X11158 / WD34X11158. The part is in stock and available at this time. Thanks, Read More...
1 Answer Hello Pete. Test for power to the control module. If there is power there and you have no lights you will need to order and replace the control module on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
J.C. January 29, 2017 for Model Number SHE4AP05UC/06 Unit will not run but just spins the pump 2 times before ending with the clean light on. I did the work around for a while of resetting the programs and it worked, at this point though it will just perform erratic operations, like filling with water and not pumping out, or just spinning the pump for a long time. Considering the symptoms and how they have changed I'm wondering if I need to change the main control board, the control module or both.
1 Answer Hello J.C., You should first check for any water in the base that could be floating the flood switch float. This will cause the issue you are describing. The symptoms seem to change when the unit is left sitting long enough for the water to evaporate out and cause the issue to cycle back around again. What causes the issue is a water valve that does not open fully, causing a dribble of water to get into the base of the unit and float the flood switch. The correction for this issue is to remove the water valve, clear any water in the base of the unit, (I "wick" the water out with a towel that has no fabric softener on it), and replace the water valve 00622058. Read More...
Amy October 24, 2016 for Model Number SHE4AP06UC/06 dishwasher previously not going to wash cycle when start button pressed. It would begin to shut down cycle with draining (same as if you depress the start button for 30 sec). Replaced the control unit a month ago which fixed the problem and dishwasher worked perfectly. Now it is doing the same thing again. I had previous advice to replace the power module. Why did the control unit fix it for a month?
1 Answer Hello Amy. It sounds like the control unit 00668460 is failing and will need to be replaced on the unit. The reason it worked for 1 month is you reset it to replace the other board. Read More...