Ric December 06, 2014 for Model Number Bosch WFL2060 UC/1 (FD8211) I just installed a new control module 481304. Saw the response to Lynn about whether we needed to adjust the switches as the instruction paper that came with the module says must be done. I'm not sure if the slightly different at the end of the appliance model # (FD8211) makes a difference or if I can also not adjust the switches after installing the unit. Thanks
Lynn September 20, 2014 for Model Number WFL2060 UC/01 (FD 8201-) How do I activate the switches on the circuit board on my replacement control module #00481304?
1 Answer Lynn, This unit does not incorporate programming that has to be done to the control module to get it to work for your unit. Read More...
Greg G August 24, 2014 for Model Number WFL2060 UC/01 (FD 8201-) Our washer won't stop filling with water on the first rinse cycle. On the initial wash cycle it's fine, but the first rinse, it won't shut off. If I turn off the water valve, it will stop filling and continue as normal. We have already replaced the pressure switch. We took off the hose to the pressure switch and it seems fine. It also seems that the first rinse cycle takes in the fabric softener instead of waiting for the last rinse. Any suggestions would be greatly appreciated.
1 Answer Hello Greg. The cold water valve 10031360 is bad and will need to be replaced on the unit. Read More...
Tracy August 18, 2014 for Model Number WFL2060 UC/01 (FD 8201-) The wash light is blinking but the machine won't start when I press the button.
1 Answer Hello Tracy, You should first check connections to the door switch. If no problems, replace the door lock assembly 00184455. If this doesn't correct the issue, the main control 00481304 would be the next suspect. Read More...
Lynne June 26, 2014 for Model Number AWFMC330UC/10 I keep getting an error E04 code. I had a Bosch authorized service tech come out and he told me I use too much soap. I didn't think I did but reduced the amount of soap to approx. 2 tablespoons per wash load, no softner or bleach. I still get the E04 code. Do I need a need control board and can I replace this part myself. This error happens on all types of wash cycles. I have to drain, run a soak cycle then drain again and spin to get the wash finished. Or drain and rerun the load on 25 minute cycle without soap.
1 Answer Lynne, Before replacing any parts you will want to try to run a clean cycle with white vinegar and the hottest water you can get to make sure that there is no soap residue that may have clogged a sensor or anything. Then you would want to try to run a cycle and if the problem persists then replace the control board. Read More...
David S. May 13, 2014 for Model Number nexxt 300 series When I start the machine it fills with water but the drum does turn. The clock keeps going. When I put it on spin the water pump pumps but the drum don't turn.
1 Answer Hello David, If the spin basket never turns you have either a bad motor control board, a bad motor, or a lost connection in the circuit. Check how drum rotates. If drum wobbles or won’t move, replace outer tub (containing faulty rear bearings). Check voltage at motor connectors when motor is energized. If low or no voltage, replace faulty motor control. If voltage ~ 120V, check motor resistance (when washer de-energized). If motor is OK, replace faulty motor control. Check voltage at motor connectors when motor is energized. If ~ 120V, check motor resistance (when washer de-energized). If motor faulty, replace faulty drum motor. Read More...
Carter April 21, 2014 for Model Number Bosch WFL2060UC/22 My 7 year-old Bosch Axxis washer works fine in all modes except for Regular/Cotton. No matter the temperature, the unit does not fully drain the washer in this mode, and I have to rotate the dial to "Spin" to drain and spin the laundry after running it. The washer drains in all other modes (e.g., Permanent Press), and also in "Spin" and "Drain" modes. I have checked the drain pump resistance and also tried replacing the drain pump, but the old one measured our fine in resistance and the new one didn't solve the problem. I also tried cleaning the various hoses and vent tubes, which were filled with gunk, but that didn't solve the problem either. Do I need a new Control Module or is there something else that I should try first?
1 Answer Carter, Based on the information provided it does sound like the issue with the unit would be a fault in the control module 00481304. Read More...
Chuck February 15, 2014 for Model Number Bosch Axxix wfl2060 washer When we select any cycle, and press start..water will enter the number 1 tray then stop, then nothing else happens. The machine stays in that condition until I drain it.
1 Answer Chuck, You will want to check the door latch assembly to make sure that it is good. If the door is not latching properly then it will sit idle and possibly shut off. Read More...
Joe April 12, 2013 for Model Number bosch nexxt 300 wfmc2201uc/13 Motor doesn't spin under load. Motor pings out ok resistance between all 3 phases and ground (infinite) and about 8 ohms between phase leads. Pointing me towards control board. Control ouputs about 30-50 volts when meter is set to a/c and about 105-150 when meter is set to d/c. I was told that this is because of the 310hz frequency of the output current. I was also told that the voltage output could read ok, but that the frequency could not be correct which would lead to less power for motor. Is there any other test I can perform on board?
1 Answer Hello Joe, Try the unit with the belt off to ensure the bearing isn't the issue. From the tests you have already run, it sounds as though the motor control module 00668952 will need to be replaced. Read More...
Brian April 04, 2013 for Model Number Control Module, Wfl 2060 I am replacing the control module. Can this be done with out removing the stacked dyer. Anything special I should know?
1 Answer Brian, You will need to remove the dryer from the unit. Once you get the top off and the control panel to where you can roll it up you will want to take pictures of where the wiring goes. It should not be too difficult as the plugs only go to certain plugins but is best to take pictures as a reference. Read More...