Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Main Control Board by Frigidaire

Best Seller
Manufacturer Part
4.89 (64)
By: Frigidaire
Part Number: OEM13076436
Manufacturer Part Number: 137006000

Washer won't start, shows error codes, or cycles randomly? The main control board manages all wash functions. Moderate DIY repair with careful handling.

More
$237.62

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Frigidaire Washer Main Control Board (Part Number: OEM13076436)

1 Answer

Hello Tamara,
I think your diagnosis is on the right track. If I had the model number so I could pull the tech sheet, I would help you further. As it stands, I can only advise you to dis-connect the connectors one at a time from the controller and related components. If your issue is caused by a poor connection, this should clear the issue for at least a cycle.

Read More...
Chad for Model Number frigidaire affinity model FAFW301LW3

I can choose different wash cyles and the time amount will change on the lcd screen. However, when I try to start it, it locks the door and all four lights come on for a second, like its trying to sense the load, then the sensing light goes out and the machine sits their idle and will do nothing. There is a faint humming noise from the lower right of the machine. When I run a diagnostic test, I get an error code that states E6E. I have checked and cleaned the pump filter to no avail. HELP PLEASE!!!!

1 Answer

Hello Harvie. You need to check and see if the pump and filter is clogged and needs to be cleaned out on the unit.

Read More...
Jeff for Model Number GLTF2940FE2

I just started getting an error code on my fridgidaire washer machine. The code is E90 and Fridgidaire themselves have no idea what that error code is. After doing some research it appears to be an issue with the main control board. I'd rather not spend 130+ bucks just to see if that works. I've reseated all connectors on the board itself but just wanted to see if there was a more sure answer to the E90 error before spending the money. Thanks for your help!

1 Answer

Hello Jeff,
E90 indicates a communications error between the user interface board (control panel) and the main circuit board. If connections have been verified, it has to be a problem with the control understanding the information recieved.

Read More...
Jim for Model Number gltf2940fs

Hello and thank you in advance. My elderly parents have a Frigidaire GLTF2940FS front load wash machine that is possessed by unseen demons. Over the past 4 years it has given almost any and every error code (most frequently one involving an open door or four lick issue - which we thought we solved by having a certified tech install a new door lock or switch). At any rate, we keep the machine unplugged as it turns on and beeps on its own at any given time. It frequently is unable to finish a lead as it will freeze or lock up. I am assuming this is a control board issue - but which board. I am given to understand that there are TWO control boards on the machine; one is "control board" AP3891780 (or 134743500) and the othe other is referred to as "main control board" part number AP4358809 (or 137006000). ID like to order asap but which board most closely fits the issues I've outlined? I'm a disabled vet and they are elderly so we are limited to fixing as opposed to buying new....

1 Answer

Jim,

This issue would most likely be in the Main control board 137006000. The other control board that you listed is the speed control board for the motor.

Read More...

1 Answer

Hello Dave. E46 Control board problem. E47 Board thinks the door PTC circuit is open in spin. Replace the control board.

Read More...

1 Answer

Ross,

The E10 error code indicates that the fill time is too long. You will want to check the water flow coming into the unit to see if it is normal. Check the to make sure that the screens on the water inlet valve are not clogged. If clogged then clear. If the water flow while filling is normal then you will want to check the pressure switch to make sure that it is good and check the pressure hose to make sure that it is not clogged or kinked. If these check ok then you will want to replace the main board.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google