Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Main Control Board by Frigidaire

Best Seller
Manufacturer Part
4.89 (64)
By: Frigidaire
Part Number: OEM13076436
Manufacturer Part Number: 137006000

Washer won't start, shows error codes, or cycles randomly? The main control board manages all wash functions. Moderate DIY repair with careful handling.

More
$237.62

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Frigidaire Washer Main Control Board (Part Number: OEM13076436)

1 Answer

Hello Snowy. If you ordered the board you posted the question under, you have installed the wrong board. You model number calls for 137005000NH.

Read More...

1 Answer

Shamika,

The E41 error code is an indication that the main control board thinks the door switch is open. The things to check. Is the loading door closed. If not then close the door and if yes then Disconnect the plug from the J2 on the main control board and check for continuity between the pins and the plug. IF it is open then check the door strike. If good replace the door switch assembly. If closed then replace the main control board.

Read More...

1 Answer

Hello Danny. Lock is testing good, so I would start with the board according to the code.

Read More...
Christopher for Model Number ATF6700FS1

Our washer has stopped spinning. The tub had drained and I checked the trap at the pump for debris which we have found full of stuff two other times but not this time. I checked codes and found E41 door lock switch malfunction. I checked the J2 connector per the instructions and found 120 volts at the black wire. It appears to be the main control board per the manual but after looking on the net it makes me wonder. One thing that I thought was odd was the pump would run when we selected spin only although no water was present. I am prepared to buy the board if need be, your thoughts?

1 Answer

Hello Christopher,
This sounds like a door lock assembly 131763256 issue as long as all of the connections have been unplugged and re-attached since many problems with these unit are due to poor electrical connections. If the door lock assembly is the issue, you will also need to order part numbers 134606800 harness and 131763310 door strike. As far as the pump running as you mentioned, there is nothing unusual about this.

Read More...

1 Answer

EH, The codes you've listed are basically communication errors between the main control board and the peripheral components. The LOC code indicates the control has been locked, so the machine cannot be used, ot there have been too many false inputs and the control has locked itself(like a computer) and needs to be rebooted ( remove power to the washer for 10 to 15 minutes, then try again). The first check you make needs to be to the wiring harnesses, between the main control and the motor control boards, and the door latch assembly and the main control board. If there are no loose or damaged wiring connections or wires, you'll need to replace the main control board 137006000 as the most likely issue.

Read More...

1 Answer

Deisy,

The control panel would weight less than 5 lbs but the box that it comes in, we could not determine the size of the box that the part ships in. The overall of the part is 14" length x 4" height x 3" depth.

Read More...
Julio for Model Number GLTF2940FS2

Hi, need your help; a week ago my Frigidaire Washer Model # GLTF2940FS2 start with a continuous Bip that was driving was crazy. Based on the error code E36 the main control board was replaced. After replaced, and performed the diagnostic test error E5E appeared, followed the recommended instructions check the wiring all Ok. Prodeed to change the "Speed/motor" control board and the E5E will not go way. during the diagnostic test the water solenoid are Ok, but the wash cycle takes a little water and stops, get the E5E error, same with the spin cycle it dups a little water and stops get the E5E error.

1 Answer

Hello Julio. It sounds like a wiring harness issue or spped board problem. You will need to check both.

Read More...

1 Answer

Hello Denny. I would try replacing the lock first. These can test good and be bad. If it does not fix the issue, send it back and order the board.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google