Doug September 29, 2017 for Model Number DE09-US0 I need to replace the front bearing and shims on my dryer. Can I use four of the white shims (WE1M504) or do I need two green (WE1M507) and two white?
1 Answer Doug, You will need to get 2 white and 2 green as this is what the manufacturer recommends. Read More...
Scott August 23, 2017 for Model Number DX4500EA2WW My dryer is making a lot of squeaking sounds once it heats up. drum moves freely when off and not a lot of play in it. I am sure i need to replace the slide pad i just wanted to know if there is more then 1 and if there is any other maint parts i should change out at the same time and if there is a kit rather then single parts. thanks
1 Answer Scott, There should be 2 green and 2 white bearing slides on this unit. There is a maintenance kit that you could get that would have both these in it and the top bearing belt and felt. The part number for the maintenance kit will be [AP58006906]. Read More...
Jared R. August 18, 2017 for Model Number dpsr610eg1wt My drier is making a loud squealing noise. I replaced the front felt strip, belt, and tensioner pulley. The noise went away for a week but has returned. I tested running the drier empty, and the noise was reduced almost to none. The plastic "bearing" on the front panel (which is not what I would normally consider a bearing since it's a giant plastic piece), looks okay. I'm thinking I need the rear bearing kit, but not sure. I'm not sure if that includes the sleeve in the kit.
1 Answer Hello Jared, Bearing kit WE25M40 does include the bearing sleeve WE1M462. This noise is commonly caused by the grounding strap WE1M1015 by the time the rear bearing kit needs to be replaced. Proper lubrication 5303307893 is necessary to prevent the noise from recurring. Read More...
Eliza M. May 11, 2017 for Model Number EGD2000AOWW Clothes are catching on cracked plastic at front edge of old GE gas dryer, top and bottom. The area matches the trap duct assembly (WE14X21334) and the dryer drum front support bearing (WE3M26) on your site. Are these compatible with my model number EGD2000AOWW? What slides/glides do I need to order? Thank you
1 Answer Hello Eliza, Model EGD2000A0WW calls for WE14X25080 and maintenance kit WE49X20697. This maintenance kit includes the upper bearing, all four slides, the belt, and felt. The only other thing you will need is the adhesive WPY055980. Apply it and let set for 10 or 15 minutes before putting the felt seal in place on it. Be sure there is not too much so it cannot get into the drum area. Read More...
Benjamin March 27, 2017 for Model Number DBVH512EF0WW I need to replace the bearing on my GE DBVH512EF0WW. The part number it says I need is WE14M124, I keep seeing part number WE3M26 pop up and I was wondering if they are the same part?
Mike March 19, 2017 for Model Number GE model # DBXR463GB0CC I need to replace the dryer drum front support bearing along with drum glides , so I just want to make sure I get the right part #'s and correct amount of drum glides.Thanks it's very much appreciated.
1 Answer Hello Mike. You will need to order WE49X20697 and it will come with everything you need. Read More...
Ron T. March 09, 2017 for Model Number DHDSR46EE1WW I am looking for the Dryer Drum Front Support Bearing part. Your part number is AP3790641 for my dryer. When I check the compatibility checker, it tells me this part is not compatible with my dryer. How do I get a Dryer Drum Front Support Bearing part that is compatible with my dryer? Thanks
1 Answer Hello Ron, I would recommend using the dryer maintenance kit WE49X20697 for your model. This is cheaper than ordering the glides individually and you get a new belt and felt seal also. We must apologize for the compatibility tool since it is in work and still not working properly. It should be disregarded at this time. Thank you for your patience and understanding in this matter. Read More...
Amanda February 28, 2017 for Model Number DBSR453GB2WW Does it matter which drum glides (White AP3206716 or gray AP5668531) are used for Par # AP3790641?
1 Answer Amanda, You would need 2 of WE03X37318 and 2 of WE03X37317 for the front support bearing. Read More...
Gary L February 23, 2017 for Model Number DWSR463GGOWW I need the top of the bearing because part of it has warn away, the back bearing and all slides necessary. I also watched your videos but they didnt show me how the bearing is held to the front of the dryer. Is it screwed on? Could you also tell me what the cost will be and when I can expect them delivered. I live in the Mpls area.
1 Answer Gary, You will need the rear bearing kit WE25M40, and the top bearing WE49X20697, The top bearing kit will have a belt, a seal and the bearing slides needed. Read More...
1 Answer James, A GE dryer will use both the Green WE03X37317 for the upper bearing and the white bearing slide WE03X37318 for the lower and you would not want to put one in place of the other. Read More...