Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Drain Pump by Ge

Best Seller
Manufacturer Part
4.89 (64)
By: Ge
Part Number: OEM17410392
Manufacturer Part Number: WH23X10030

Washer won't drain or leaves clothes soaking wet? This drain pump removes water from the tub after each cycle. Typical DIY repair takes 20-30 minutes.

More
$56.68

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Ge Washer Drain Pump (Part Number: OEM17410392)

1 Answer

Lorne,

You will want to check the pump to make sure that there is not anything that is clogged or obstructing proper drainage. Also make sure that you are not overloading as this would also cause the issue.

Read More...

1 Answer

Hello Carey. If you can stop the water from entering the machine by turning off the timer or unplugging the unit, you will need to look for a bad pressure hose or replace the pressure switch. If the only way to shut off the water is at the shut off for the water hoses, you will need to replace the water valve in the unit.

Read More...

1 Answer

Hello Red. You need to make sure there are no clogs. If not, you will need to order and replace the pump on the unit.

Read More...

1 Answer

Tiff,

When the unit is supposed to go into the spin cycle you would want to check for power to the motor to make sure that the timer is sending power to the motor. If you do not have 120 vac to the motor then either the timer is faulty or the wiring but would most likely be the timer. If there is power to the motor but it is not running then you would need to check the windings to make sure that they are not bad and check to see if the brake is releasing in transmission. If the brake does not release then the unit will not spin.

Read More...

1 Answer

Dani,

You will want to check voltage on the inverter board of the motor for 120 vac. If you do not have 120 vac then the in line fuse in the wiring harness is bad and will have to be replaced. You need to check Connector C2 pins 3 and 5. IF there is no voltage then follow white/red wire up from pin 3 and you will find the thermal fuse approximately 1/2 way up tub in the harness. You will have to cut out and replace the fuse WH49X10055.

Read More...

1 Answer

Hello Roy. No, you need to release the clips in the top using a flat bade and remove the front panel. Then run the washer and look for the leak. It could be a bad flood gasket on the unit.

Read More...

1 Answer

Hello Anthony,

You will want to check the pump for obstructions but also you want to check the vanes of the impeller to make sure that they are not damaged. If there are damaged vanes it would cause unit to not drain properly. If this is the case then you would want to replace pump.

Read More...

1 Answer

Hello Lawrence. If you can stop the water from entering the machine by turning off the timer or unplugging the unit, you will need to look for a bad pressure hose or replace the pressure switch. If the only way to shut off the water is at the shut off for the water hoses, you will need to replace the water valve in the unit.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google