Dianne W August 03, 2015 for Model Number JGBT35BEA4BB Hi The flames in our oven shoot up the sides an are very high.The oven also has very bad strong odor, whenever I use it. My husband was wondering where the orfus is for oven so he can turn it down. If you could send me diagram and how to fix it would be great. Thank you, Dianne
1 Answer Dianne, The orifices will be located on the oven safety valve located in the back of the unit. It sounds like the unit was converted to LP but maybe the oven was not converted. To do this you would need to get to the safety valve and tighten the orifice all the way down and open the air shutter on the burner. Read More...
Butch June 19, 2015 for Model Number GE - jgbp79beb6bb I'm not sure which part to purchase? Bake & Broil do not work. Stove top does work. Both Bake & Broil ignitors light to an orange color. I made an ohms reading on the Bake ignitor with a results of 250 ohms. I made an ohms reading on the safety valve with a reading of 1.7 ohms. Can you help?
1 Answer Hello Butch. If both bake and broil went out at the same time, you will need to check the oven control WB27T10350 on the unit. If it is not sending power to the igniters, then it will need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John C June 11, 2015 GE gas wall oven oven igniter is not getting enough volts to make it glow. The broiler igniter works fine, and I tested it to see that it gets about 120 v. when I power it up. When I power up the oven, the wires to the igniter are only getting about 25-50 v. Any idea on if and how I can fix that??? Thanks, John
1 Answer John, With the igniter getting only 25 to 50vac then you will want to test the thermostat or control board (depending on what your model has). This would be the most likely cause for igniter to not come on. Read More...
Rowdy May 19, 2015 for Model Number JGBS23BEA2AD On the over part there is gas going to the safety valve and the igniter is glowing but the oven won't light I tested the safety valve with a digial multimeter with the oven on and it only showed 1.4 v does this still mean the igniter is bad I seen where you said it should read 3.2-3.6 v. Thank You in advance for you time and information.
Sue May 19, 2015 for Model Number GE XL44 Gas Range My oven temperature is 50 degrees. Is there a replacement temperature control unit for oven?
1 Answer Sue, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Dave G. March 03, 2015 for Model Number RGB526DET2WW Oven would NOT stop heating up. Unplugged unit. Now oven and broiler will NOT light.
1 Answer Hello Dave. It sounds like the thermostat WB20K8 is bad and will need to be replaced on the unit. Read More...
Cassius W. January 28, 2015 for Model Number PGR4410BDW Will the ignitor shown in the video fit my oven: maytag performa serial: 11284808yw ?
1 Answer Cassius, The oven igniter that is listed for your unit would be part number WP7432P136-60 and part WB13K21 will not work due to a different style of bracket. Read More...
Mike January 05, 2015 for Model Number JGBP30wea8ww Bought a GE XL44 gas range 12 years ago. Replaced igniter 4 or 5 years ago and fixed problem. Classic symptoms....igniter slow to glow, oven didn't get very warm and food slow to cook. Last 2 months after reaching operating temp we've heard an occasional "puffing" or soft popping sound. We did not hear this sound when the first igniter went out. Wife thinks food is taking a bit longer to cook. Took oven floor pan off to look at igniter. Takes 15 seconds to start glowing. About 1 minute for gas to ignite. Ends do not glow. Only middle third gets white hot, rest of element orangish red. Is the igniter going out again? Is this the typical life span? Is it something else like the temp sensor element or gas valve? TIA.
1 Answer Hello Mike. Yes, you will need to replace the glow igniter on the unit. It is getting weak. Read More...
Troy December 29, 2014 for Model Number 362.75320101 I am replacing oven igniter #AP2020569. My stove is propane not natural gas. Will this be okay?
1 Answer Hello Troy, This ignitor WB13K21 is the one recommended by the manufacturer so it will work fine. Read More...
Wendy November 11, 2014 for Model Number ge spectra model 317B6641P001 Hello, I have a gas oven( ge spectra model 317B6641P001).Our oven has stopped working. Burners and broil are fine but oven wont heat. Trying to fix this ourselves and avoid expensive service call. From what I have read some articles suggest igniter could be the cause. Any ideas what to try first, or if you have heard of this issue? thanks so much Wendy
1 Answer Wendy, Start with the oven igniter. 95% of heating problems on a gas range/oven are due to a weak or broken igniter. Your post information would indicate that's where the issue is. The model number you supplied is incorrect so recheck the tag or visually inspect the igniter. You may be ordering the incorrect part for your range. Read More...