Torris July 14, 2014 for Model Number wm2016cw I received the LE error code on my washer. A few days later the entire washer went dead. I tried resetting it but nothing happens. I checked the power outlet and its getting power. What part or parts should I order?
1 Answer Hello Torris. LOCKED MOTOR ERROR. You need to check: • The connector (3-pin, male, white) in the MOTOR HARNESS is not connected to the connector (3-pin, female, white) of STATOR ASSEMBLY. • The electric contact between the connectors (3-pin, male, white) in the MOTOR HARNESS and 4-pin, female, white connector in the MAIN PWB ASSEMBLY is bad or unstable. • The MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut (open circuited). • The hall sensor is out of order/defective. Read More...
Chris July 06, 2014 for Model Number Lg washer 3850EN-3093z I bought the washer from USA and took it to Nigeria. I called technician to install it and he plunged it to 220 volts normal Nigeria voltage and it had problems. Could you tell me what are the possible parts that could be affected so I can order the parts. Thanks.
1 Answer Chris, The model number listed is not showing as a valid model number. Most likely you will need the line filter and the control boards for the unit. Read More...
Keith April 24, 2014 for Model Number wm2455HW Washer does not wash clean anymore. Clothes does not get wet enough. Been this way for months. Used to see water kind of running over the front bottom seal but now barely. No error codes. Removed the Air Chamber - no blockages. No air restriciton when blowing thru the inlet hose. Tried washer again - still same issue. Have replaced the pressure switch, removed and reseated the connectors at the main PCB board - still same issue. Have PDF manuel for trouble shooting this model but the washer is not broken enough to generate any error codes. Is there a factory reset that could possible resolve this problem or something else I can check just shy of replacing the Main PCB? Would appreciate any help. Thanks
1 Answer Hello Keith, You need to check the screens in the water valve and check for screens in the inlet hoses. If there are none or they are clear, it is most likely a water valve not allowing the water to enter the unit at full pressure. Read More...
Rick January 31, 2014 for Model Number WM2016CW A service tech said I need a main board for my LG washer. I am trying to find the part number.
Broken Lg January 13, 2014 If I order the PCB board, and this happens to be the part which is not defective on my LG washer, can I return the board for a full refund? Thanks
1 Answer Hello Broken LG. You can return the board, but it is minus the shipping and handling and return shipping. Read More...
Tj June 15, 2013 for Model Number wm2016cw Hi, I have a LG washer that gives a OE error code when it drains. It will drain the water fine but it will keep draining and pausing for about 10 mins then throw this OE error something about not draining check restriction in drain or pump. I checked the drain hose, pump, pressure dome, pressure switch, and wires. They all seem ok so I replaced the pressure switch and still the same problem. Could it possibly be I need to change this PCB board?
1 Answer TJ, You will want to reach into the drain pump and check the impeller to make sure that when you spin it there should be a magnetic type catch when spun. Also check the tube at the bottom of the tub to make sure that there are no restrictions in the tube. If all checks ok then replaced the control board. Read More...
Holly December 18, 2011 Do you work at weekend? I have placed an order: #2280126, so far, it seems like you have not processed it yet? Thanks
1 Answer Hello Holly. Based on the order number you provided, it shows your PCB assembly EBR32268001 was shipped today. Hope this helps. Read More...
Holly December 16, 2011 for Model Number LG WM2016CW The technician told us the board (A450) might need to be replaced, I didn't know the A455 is the cover. So I may not need to buy it (A455), Any suggestion? By the way, if I buy A450 from you, after it is installed, my washer is still not working, can I return it to you? Thanks
1 Answer Hello Holly. No, you can use the old cover on the PCB assembly EBR32268001. If the board odes not fix the issue, you can return it. Here is a link to our return policy. Hope this helps. http://www.appliancepartspros.com/customerservice/returns.aspx Read More...
Holly December 16, 2011 for Model Number wm2016cw Hi there, when I buy A450, it comes with A455 together? thanks.
1 Answer Hello Holly. No, the PCB EBR32268001 does not come with the cover 3550ER1032A. It will need to be ordered separately. Hope this helps. Read More...