Peter September 11, 2014 for Model Number WM2277HW I am all the way into the 16th minute of this video, and for some reason the inner basket does not want to come out completely. I banged on it with a hammer and a piece of wood like in the video but it is sticking in some place & I do not know what to do now. FYI, the outer bearing is broken, so couple of the balls are out, also the shaft is couple of inches down, it appears that I am almost there but it is not coming out. Do you have any tips that can help?
1 Answer Hello Peter, If the spin basket 3045ER1006E will not come out it will most likely need replacing. This is an indication that the spinner support assembly has excessive wear and would only wear out the new bearings if re-installed. Read More...
Bob J September 09, 2014 for Model Number 4174104200 Will these bearings and seal fit a Kenmore front loading washer, model #4174104200? AP4439183, AP4437603, and AP4438637?
1 Answer Hello Bob! No, the seal and bearings are not listed as being compatible with your Kenmore washer model 417.4104200. Unfortunately, for the model given, the manufacturer does not offer the bearings and seal separate from the outer tub assembly, part number 131525500. Sorry about that! Read More...
Joe August 09, 2014 for Model Number WM2277HW I'm changing the bearings on my LG Tromm. I can't get the inner tub out from the outer tub. I've used WD40 and hammered it and it won't budge. If I remove the 18 bolts from the back of the outer tub where the shaft is sticking up will this be helpful?
1 Answer Hello Joe. No, if the front tub is removed, the inner basket should come out. Make sure you have removed the rotor and stator from the unit. Read More...
Jim July 17, 2014 for Model Number LG wm2501hwa I'm replacing my seal on the washer! the seal is so loose that it just fall in and is not tight at all, and if you turn it over the tub that is it falls out! What should I do?
1 Answer Jim, Based on the description it sounds like the opening for the tub bearing has opened up and the only thing that can be done is to replace the rear outer tub. Read More...
David May 26, 2014 for Model Number Whirlpool washer wfw9150ww01 Do you have shaft seal for whirlpool washer? Thanks.
1 Answer Hello David! The shaft is now only available with the basket part number WPW10202459 and the seal is only available with the outer tub part number W11239040. Sorry about that! Read More...
Michael March 18, 2014 for Model Number whirlpool ghw9100lw1 Do you have seal for my model which is the same looks as AP4438637 ???
1 Answer Hello Michael. No, you must order and replace the outer tub assembly W10772617 to replace the seal in the model number provided. Read More...
David M December 10, 2013 for Model Number WM2277HW The gray door seal on this front loading washer has a tear in it and is leaking. What is the part number for the replacement?
Scott October 26, 2013 for Model Number 110.23822100 I have a direct drive Kenmore 80 Series washer with a leaky transmission. Is there an oil seal available that will replace the original one on top?? If so, what is the part number?
Winfield July 24, 2013 for Model Number wm0642 I am replacing the inner tub, outer seal. There is no direction on the seal saying what side goes in first. Any guidance?? Also a little silver spring just popped off it. Im assuming this goes on the outside of the lubed flange?
1 Answer Winfield, The silver spring does go on the outside of the lubed flange. The Seal will go in with the spring facing the bearing. Read More...
Mike P July 24, 2013 for Model Number WM2277HW Which way does seal ap4438637 face? Spring side towards the drum or towards the bearings.