Jl May 25, 2021 for Model Number DW7933LRAWW/AA Soap dispenser won't open during cycle. Replaced dispenser with no difference. Cycles won't progress. No errors codes. Is there a humidity sensor that needs replaced? What else could it be?
1 Answer JL, With the dispenser not opening and having already been replaced, check the wiring between the main control board and the dispenser and if the wiring is good then the control board would be the issue. Read More...
Jose October 08, 2018 for Model Number DMT400RHS/XAA The dishwasher start normally, after 4 minutes stops, drains and start blinking “smart auto”. Stay like that forever if you do not turn it off.
1 Answer Jose, This error would be a water supply error. Check the water valve for debris in it. Check to make sure that there are no loose connections at the valve. If this checks ok then either the water valve or the main board will be the issue. Read More...
Scott April 12, 2018 for Model Number DMT400RHS/XAA My Samsung DMT400 begins to fill, but then about sixty or ninety seconds in it stops and drains the tub. Then, Normal, Heavy, and Smart Auto lights all flash together. I've cut power and then restored hoping to cure but no change.
1 Answer Scott, This issue would be caused by a faulty water level sensor or a bad main control board. Read More...
Joseph K February 13, 2018 for Model Number DMT400RHS/XAA Normal setting light is blinking Dishwasher starts begins cycle and stops.
1 Answer Joseph, If just the normal light is flashing then this would most likely be an erroneous error and would be a faulty control board. Read More...
Seimon Geller August 26, 2017 for Model Number DMT800RHS I have an error code PE, according to the manual it's half load function error. I pull out the fuse braker did not helped. Please advise what is my next step Looking forward hearing from you soon.
1 Answer Seimon, The PE Half Load Function error code refers the the "diverter" motor on the bottom of the wash pump assembly DD31-00010A and/or the switch DD34-00004A. You'll need to check the wiring between the motor , switch and control board. The motor should have 3 to 4 K ohms resistance across the terminals, and the switch should be activated and have a closed circuit. if the motor and switch check OK, then the control board DE92-02256A is at fault. Read More...
John December 29, 2016 for Model Number Assy-Case SENSOR;DMT800 I just purchased the Assy-Case SENSOR for my Samsun dishwasher DMT800 but I have no idea where this goes. Can you please give me some instructions on how to install this item please? Thank you so much
1 Answer Hello John, You will need to pull the dishwasher out to access the left side, (as facing the unit). It is strongly recommended to take several pictures from different angles to refer to during re-assembly. Read More...
Archie November 03, 2016 for Model Number DMT-400RHS/XAA My dishwasher case sensor filles up with water until water hits top then pumps it back out. I put a new case sensor DD94-01006A on as well as the Break case DD94-01005A and no differance now what????
1 Answer Hello Archie. It should put the water into the tub and not fill up the case assembly. If it is filling up the case assembly then the fill system of the dishwasher needs to be checked for a blockage. If it over fills the tub, then check the water valve to see if it is stuck open. If not, then either the wiring harness is bad or the control board is bad on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mike November 01, 2016 for Model Number DMT400RHS My dishwasher runs with no problems, however, there seems to be an excess of water in the tub inside when it runs. So much that it is dripping out of the bottom of the closed door. I have removed the case break assembly and the float and cleaned them out and this helps, but still a little dripping from the door when the dishwasher cycles. Is it possible one of these parts needs to be replaced?
1 Answer Hello Mike. It sounds like you will need to replace the case break on the unit. Also, make sure your not using to much soap in the unit. Read More...
Maria August 08, 2016 for Model Number DMT400RHS/XAA I need to buy this part DD61-00267A (left side) for my DMT400RHS/XAA Samsung dishwasher. Is there any compatible part I could buy. Thanks
Kortney S. July 07, 2016 for Model Number DW80F600UTS/AA-0000 The smart-auto and heavy lights blink shortly after starting a load of dishes. Manual says its an over level water error. Can you please help me try to fix this problem?
1 Answer Hello Kortney, This is an over-level water error. As per the manufacturer this can be caused by the flow meter DD82-01373A, water valve DD62-00084A, and/or the Main Power Control Board DD92-00033C. Read More...