T Carle February 08, 2023 for Model Number dvg45r6300v/a3 My samsung gas dryer starts, burner kicks on for 30 sec. then shuts off. timer goes to 1 minute. On the timed cycles that bypass the moisture sensor, same thing. kicks on once, clicks off. I have replaced everything except the blower switch and start switch, both test fine. Iam talking new control and display board, new gas valve, new thermistors (both) and new high limit switch. I took the drum out and the spring off the belt switch so I could watch what happens, and the ignitor kicks on, the flame switch opens the valve, the burner roars for 30 sec. and thats it. What could I be missing? I put a wet rag on the moisture sensor for the cycles that use it, and same thing! (vents clear) model dvg45r6300v/a3
1 Answer T Carle, Check the venting of the unit all the way to the outside of your home. Clogged venting can cause this issue to occur. Read More...
Dave August 23, 2022 for Model Number DV2C6BGW/XAA-0000 The gas dryer heats for a short time (between 0 and 120 seconds) and then the burner turns off. The dryer turns, there are no error codes. The dryer runs its full cycle, but the clothes are still wet. I have replaced the Samsung thermal fuse, AP4201894 and Dryer Thermistor AP4201716 however those parts changes did not solve the problem. What do you recommend I try next?
1 Answer Dave, it would be recommended that the dryer duct, and the duct going to the outside of the house, are cleared of any build-up that could be preventing proper airflow. Testing the main control for 120VAC at the blue wire on the heater relay would be necessary as well. If the vent is clear and there is not voltage after a 2-minute period, the control has failed. If there is voltage and the duct was clear, the ignitor DC47-00022A would be the most likely cause of failure. Read More...
Sid May 08, 2022 for Model Number DV331AGW/XAA Hello, My dryer heats up but then goes cold. Exhaust is clear so there is no issue there. No problems with spinning or other normal operation. I tried running the cycle with the door open and I get an initial burst of hot air but then nothing at all. Could it be this part or thermistor or cycling thermostat? Thanks, Sid
1 Answer Sid, It sounds like there may be an issue with the gas coils on this unit. You will want to test the coils for resistance to make sure that they are good. You can test the coils using a multi-meter. The two prong coil will read 1,000-1,300 ohms, and the three prong coil will read 1,300-1,400 ohms across prongs 1&2, and 500-600 ohms across prongs 1&3. If the coils are bad then you could use the coil kit 279834. Read More...
Nolan April 18, 2022 for Model Number DV395ETPASU/A1 Can you reccommend best part No for Samsung electric dryer Hi-limit Thermostat 2. I see DC47-00018A and I see DC47-00017A which has a slightly raised mounting plate.
Usaveteran August 28, 2020 for Model Number DV328AGR/XAA Hello - I have a Samsung front loader gas dryer. I cleaned the outside vents, duct hoses, inside duct tube of the machine and made sure the filter and surrounding areas are clean. The dryer heats up upon starting, but soon turns cold after a very short time leaving clothes wet and damp. The tub spins ok, but I upon opening the rear of the machine I found a broken drum wheel inside. Looks like the center sheared off of the spindle (still attached to bracket). I was thinking of a new thermal fuse and a dryer thermistor. Do I need to replace the thermostat(s) as well? Please advise. Thanks.
1 Answer USAVeteran, if the wheel that sheered off is the one near the motor, it would be the idler pulley DC93-00634A and it is responsible for allowing the motor to receive voltage through the broken belt switch sensor. If the arm of the idler pulley is not being held up by the belt going around the wheel, the motor will not be able to spin which will then stop the heat from being able to turn on in the dryer. The thermostats can be tested for continuity when the dryer power cord is unplugged to identify if they have failed or not. They should have continuity at room temperature. Read More...
Aj January 17, 2020 for Model Number Samsung DV5451AGW/XAA 01 My part number varies slightly from the one shown. Lines 1,2,4 match perfectly but line 3 on my part says S1124. Does that make a difference?
1 Answer AJ, the thermostat DC47-00017A is a revised version of the original and will operate the same. Read More...
Jan P. April 13, 2019 for Model Number DV50F9A7GVW/A2-0000 My dryer runs but I am getting little to no heat. What parts should I order?
1 Answer Hello Jan, You will first need to verify that the thermal fuse DC47-00016A is not open and the ducting to the outside is clear and a full 4-inch diameter. If good, the most common cause of this complaint is a failed ignitor DC47-00022A. Read More...
Tom November 10, 2018 for Model Number DV405GTPAWR/AA Dryer stops running after a few seconds, you hear the gas igniter trying to start then dryer stops, timers continues and the dryer starts and stops when the gas try to ignite?
1 Answer Tom, If the dryer drum is stopping as well then this will most likely be caused by a venting issue or a main control board issue. Read More...
Rebecca K October 07, 2018 for Model Number DV316LGS/XAA Dryer wasn't heating properly so we replaced the thermal fuse and thermistor. We also cleaned the moisture sensor and the dryer heats right up with nothing in it but won't heat with wet clothes. What can we try next?
1 Answer Rebecca, It sounds like you may have a weak motor that is not rotating fast enough when there is a heavy load in to get the centrifugal switch to make contact for the heat. Read More...
Young Kim April 08, 2017 for Model Number DV410AGW/XAA The power is on, the light comes on, and you hear a ding dong. It does not work. If the fuse goes out, can these symptoms occur?
1 Answer Young Kim, Yes these symptoms it would be either an issue of a bad thermal fuse or a faulty door switch. You will want to check both of these for continuity. Read More...