David C. October 10, 2011 for Model Number ghw9400pl1 What is the reason AP3597347 (8182119) - Front bellow tub seal will come off after it's secured by the clamp pretty good.
1 Answer Hello David. If the bellow WP8182119 is not installed correctly and the clamp good and tight, the bellow will come off. It needs to be installed properly and the clamp needs to be tight. If you pull on it and it comes off, then it is not installed properly. Hope this helps. Read More...
Rita B. September 29, 2011 I order the bellow seal for the washer and I did not get the diagram are instruction on how to install it?
1 Answer Hello Rita. We will need your model number to help you with this. Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Dj September 22, 2011 for Model Number WFW9200SQ03 What is the correct # of the front bellow tub seal for my front loading whirlpool duet. Thanks, David
1 Answer David, The "bellows" part number for the model number you supplied is WP8182119. Thanks and Good Luck Read More...
Brian September 21, 2011 for Model Number GHW9150PW0 Is part # AP3597347, AP3672823, and AP3672824 the proper parts for this model washer?(Seal, Clamp, Clamp) Ser. #CSS2815360. Your description states fits Many Models is why I ask.
1 Answer Hello Brian. Yes, based on the model and serial number you provided, WP8182119 bellow, WP8182210 clamp, and W10902779 clamp, are the correct parts. Hope this helps. Read More...
Lee September 15, 2011 for Model Number wfw9050xw00 The seal that goes around the tub and seats next to the bellow has come off. What is the part number for this piece and how do I replace it?
1 Answer Hello Lee. If you are needing the clamp, you will need to order WP8540108. If your needing the beelow, you will need to order WPW10381562. Three screws secure the washer top at the back of the washer. Remove the three screws and lift the top from the washer. Disconnect the Touch Pad/LED Assembly ribbon connector from the left side of the Central Control Unit (Fig. 4-5) and release it from the wiring harness brackets on the right side of the washer top. Remove the detergent dispenser drawer by pressing down on the release tab at the back of the drawer (Fig. 4- 6A) and pulling it completely out of the washer. Once the drawer is removed, remove the screw in the recessed hole next to the drawer opening. Release the tab securing the right side of the console to the washer. Open the washer door and place a flat-bladed screwdriver into the slot in the bottom center of the console. Push the console up to release center console tab. Be sure the ribbon cable clears the cabinet frame. Ease the edge of the boot off of the lip of the washer front near the door switch. Next, remove the three screws securing the toe panel to the front of the washer and remove the toe panel by lifting slightly and pulling forward. Remove the two screws securing the bottom of the front panel to the washer, and the two screws securing the top of the front panel to the washer. The front panel can now be removed from the washer. The boot can be completely removed from the outer rim of the tub assembly. Carefully pull the boot from around the water inlet and window washer tubes. Remove the boot retainer clamp by loosening the clamp screw located at the upper right of the tub opening. The boot can now be removed from the tub. Hope this helps. Read More...
Susie September 05, 2011 for Model Number WFW9150WW00 Hello, our Whirlpool Duet washing machine broke on Thursday (ugh!). It was making funny sounds and my husband noticed water on the floor. After researching appliance repair service men in the yellow pages, a gentleman came to our house that afternoon and charged us $50 to look at the unit. His receipt says the machine needs a new below or gasket and when he called on Friday, he said the part is on back-order for 3-4 weeks and could cost us near $300 to fix. The unit is only 2.5 years old but is not under warranty. What should we do?
1 Answer Hello Susie. Based on the model number you provided, WPW10381562 is the correct bellow. At the moment our ETA is 10-12-2011. This date is subject to change at any time the manufacture is unable to keep their promise date with our company. Thanks. Read More...
Nicholas W. August 17, 2011 for Model Number GHW9150PW1 What is the right bellow for my Whirlpool Duet washer?
1 Answer Hello Nicholas! The front bellow for your Whirlpool Duet Washer model GHW9150PW1 is part number WP8182119. Thanks! Read More...
Martha August 17, 2011 for Model Number FL5053/1 i BOUGHT THIS WASHER IN MORROCO ABOUT 6 YEARS AGO I NEED THE FRONT DOOR SEAL THE NUMBERS I GOT FROM THE MACHINE ARE ALL THIS ONES THAT I HAVE CM5834 4619 710 5488 2 EPDM MOD FL5053/1 220V 50HZ 10/230W 5.OKG 12NC 857050586103 THIS IS THE INFORMATION THAT I HAVE SEE IF YOU CAN DO SOMTHING FOR MY WASHER THE WASHER IS NOW IN PERU AND I CANOT FIND THE PART THER WEITING FOR YOUR ANSWER
1 Answer Hi Martha. What name brand is it exactly? The numbers you have provided was the serial numbers. We will be glad to assist you further. What is the model number exactly? Thank you. Read More...
Debbie August 02, 2011 for Model Number MAH2400AWW Is this the part for this model of washer? Should I buy replacement spring also or can mine be reused?
1 Answer Hello Debbie! No, part number WP8182119 is not the correct door boot used on your model. For your unit you will use part number 34001118. You should only need to replace the clamps if they are broken, if they are ok you may reuse the existing ones. Thanks! Read More...
Jim S. August 01, 2011 for Model Number WFW9400SW02 I need to know the part number for the front tub seal on my Whirlpool Duet HT.
1 Answer Hello Jim! The front bellow seal on your Whirlpool Washer model WFW9400SW02 is part number WP8182119. Thanks! Read More...