Billie M June 06, 2013 for Model Number KUDK03ITW113 My door will not lock in place. When I take the panel off, I am not sure if I need a handle, and the assembly or what. Can you provide any assistance.
Nayan P August 22, 2012 for Model Number KUDIOIILWH2 On the front panel there is no lights on any of the button either start, normal or heavy cycle. Replace the new control board ap3775506(8564543). Check power on the cntrol board ,fine 110v ac. Not working, please advise. Thanks
1 Answer Hello Nayan. Based on the information you provided, it sounds like the fuse 8193762 is bad and will need to be replaced on the unit. Read More...
Habitat Repair Guy July 28, 2012 for Model Number Kenmore dishwasher 665-13249K900 The door is very hard to close. Nothing is jammed or stuck in the door. I just have to push hard for it to close. Are there adjustments I can make? Checked the handle it seems Ok.
1 Answer Hello. There is no adjustment that can be made, but you need to make sure the unit is level. If it is level, you want to make sure the gasket is not binding the door on the unit and needs to be replaced in the unit. Read More...
Jeff March 23, 2012 for Model Number 66513672K600 Jeff again...this model dishwasher has neither a high temp scrub or air dry option. It has high temp wash, which I pushed with heated dry in place of the air dry option. Nothing happened. I tried this twice once when the machines normal wash and cancel drain light was blinking and again after I hit the breaker to stop the lights. No response either time. Is there some other way to reset this particular model?
1 Answer Jeff, Wasn't sure what nomenclature you had on the control panel here's more information "HIGH TEMP SCRUB, AIR DRY, HIGH TEMP SCRUB, AIR DRY Or SANI RINSE, AIR DRY, SANI RINSE, AIR DRY (Note: HIGH TEMP SCRUB = POWER SCOUR = HIGH TEMP SCOUR) (Note: AIR DRY = NO HEAT DRY = ENERGY SAVER DRY). Remember, you need to press the buttons, in sequence, within 6 seconds to start the test run. Thanks Again Read More...
Jeff March 23, 2012 for Model Number 66513672K600 When I try to start my dishwasher the normal wash light and the cancel drain light begins to blink. I shut off the power to the dishwasher and they of course went off. When turned back on they remained off until I hit a button to start the washer and the normal wash began to blink again. I read on one of the forums that it was the door latch...that the door is either not closed enough or it is sensing that it is open. It actually doesn't feel like it is closing with the same certain click that it used to. Not sure which of these door parts to purchase and is it difficult to replace? Thanks
1 Answer Jeff, You most likely have an issue in the control panel/keypad assembly WP8558196 but you do want to check the door switch circuits with a multimeter and insure they are a "closed" circuit when the switches are activated. Here are the basic "diagnosis" programming "HIGH TEMP SCRUB, AIR DRY, HIGH TEMP SCRUB, AIR DRY " program the cycle and let the dishwasher run until it shuts off, this will reset the control board, and it should run one "reprogramming" cycle. To access the door switch assembly, you will need to remove power to the unit, Remove the six (6) screws securing the control panel to the door frame. The control panel will now drop down and be free of the door assembly. The wiring harness will remain connected to the console components. Here's some meter usage information should you need it [http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html] , Good Luck and Thanks Read More...
Ken K. December 04, 2011 for Model Number kudm01tjwh08269906 Theres a micro switch thats located on the bracket lactch ,thats the part I need. Please let me know what part number it is. Thank you.