David August 10, 2012 for Model Number WHIRLPOOL Control Board (Part Number: AP3767528 But the water valve works OK. It is just getting the signal to be open more (longer) than it should. Te water valve cycles open and closed until the washer is too full and then sets a code. Do I need to change the control board? Any tests to prove this before making the expensive plunge?
1 Answer David, What code is in the display ? You want to start at the water level switch WPW10514214 and air dome hose WPW10004260. These are the components that control the amount of water in the tub. If the hose is clogged with sediment or debris, or if the water level switch contacts are corroded or defective, the wsher will overfill, or could produce a false code, if the switch doesn't react within a preset amount of time. Thanks Read More...
David August 01, 2012 for Model Number ghw9100cw1 Front load Whirlpool won't stop adding water (off and on) until too full and sets error code. Flow sensor replaced. Wiring looks OK, no obvious corrosion or unplugged wires, but not tested. Any suggestions?
1 Answer Hello David. Based on the information you provided, the water valve is bad and will need to be replaced on the unit. Read More...
Janet C July 23, 2012 for Model Number ghw9100lw2 My duet will start running . Then within the first few minutes it will start beeping and flashing a f and then 5. You can pause then restart and it will be fine after that. I had a repair man out he thought it was a hot and cold valve. Because when you start it and it stops the water in the machine was cold.
1 Answer Hello Janet. Here is the f/05 error code: Water Temperature Sensor ErrorIf during the water heating step in the wash cycle, the water temperature sensor(NTC) value is out of range, or the heating element circuit has failed, the “F/05” errorcode will be displayed.Potential Causes• Check the Water Temperature Sensor, Heating Element and Element Relay• Check connections to the Sensor, Heating Element and Relay. Since the model number you provided does not use the NTC or Heater, it may be a board issue with the unit. However, if no hot water is working on the valve, you will need to replace it as well. Read More...
Greg June 26, 2012 for Model Number 110 45091 404 I have a Kenmore Elite HE4t Model Number 110 45091 404. The Washer stops at the end of each cycle and needs to be stopped and reset, followed by starting the next cycle by manual selection. It runs normally in the given cycle. I have looked at a number of posts and message boards, but have not found the error code that my machine gives It flashes F followed by 33. From everything that I have read, I am assuming that it is a problem with the CCU and I will likely need to replace. Have you seen the F33 error code?
1 Answer Hello Greg. There is a tech sheet in the toe panel of the washer. It sounds like the CCU WP8182221 is the issue with the unit as it has a communication error. Read More...
Ben S March 25, 2012 for Model Number Whirlpool GHW9100L Stopped working after last wash, tried all forms of reset and entering diagnostics per the technical manual and online. No fault codes or led's of any kind, no click when plugging in, checked voltage through line filter to CCU and it is 120v, so power is there. Do I need to replace the CCU or should I check other controls?
1 Answer Ben, You're on track, based on your post, there is a "line" relay that should "click" when power is applied to the unit. The only other check to make first, is the harness between the CCU and The UI board, Then go at the CCU WP8182221 Good Luck and Thanks Read More...
Tom March 07, 2012 for Model Number ghw9100lw1 Machine washes, rinses, pumps out water, but does not go into spin cycle. What to check out to determine problem?
1 Answer Hello Tom. You will need to test and see if the motor control board W10756692 is sending power to the motor during the spin cycle. If so, and the motor does not spin, replace the motor. You can test the motor before replacing it as well. It should read around 6 ohms across pins 1 and 2, and then 2 and 3, and last, 1 and 3. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Colin January 24, 2012 My duet front loader door won't unlock. I know the CCU unit is defective. Have clothes in the washer for last several days and wife says it didn't complete the wash cycle. How can I open the door; can I force it open? If it's forced open what are consequences?
1 Answer Hello Colin. Disconnect the power and remove the top panel or the toe panel off the unit. Once removed, you will access the bottom of the door lock assembly and pull the clip on the bottom to unlock the door on the unit. Hope this helps. Read More...
Cathy January 16, 2012 for Model Number GHW9150PWO Whirlpoopl Duet Door lock light on, door open, when you push control on no response but when you hold control on and stop button the heavy cycle lights up and temp. etc with door lock light still on. No noises, no clicking. Replaced the latch system and still same problem. Is this a CCU and how long for delievery?
1 Answer Hi Cathy. Inside the washer cabinet in a folded packet is a folded up tech. sheet. Use this to assist. in a field diagnostic mode. This will pop up fault codes that will tel the elect. circuit failure. This includes the wires giong back and forth from the device to the central control board. Follow these instructions with the tech. sheet as it may be a simple wire reconnection. Remove power. Remove the 3-screws that hold the top panel onto the cabinet. You will find the tech. sheet and examine all the wires going to the motor control, motor and the tach. sensor on the motor. all going back up to the main control board part # WP8182695. Also make sure the pump hoses are clear and the pump itself is clear and the impeller does not spin loose on the pump shaft part # 280187. Thank You. Read More...
Tlc October 02, 2011 for Model Number ghw9100lq1 we just moved and when I plugged it in the display flashed then finally read 8:88 and that is all it will do. wont reset or anything else.
1 Answer Hi Tlc. Double check the fill hoses for pressure and make sure the inlet screens are not clogged. Is the door switch shutting completely? Remove the top/back and inspect all wires to see if they are plugged in tight. Are any of the control buttons stuck? Usually the user interface board part # is WP8181905, and the C.C.U. board needs replaced. Part # is WP8182221. Try the C.C.U. first and then the interface. Thank you Read More...
1 Answer Hello John, it sounds like you might have to replace the user control WP8181905. Hope this helps! Read More...