Jerry H April 15, 2013 for Model Number du1100xtps7 Most lights kept blinking randomly. So I replaced control w10084141. It took care of the problem for two months. Now it blinks back and forth between pots and pans and normal. None of the key pad buttons respond, no diagnostic procedure, no cancel and drain, nothing it doesn't do anything. Reset the dishwasher, breaker at the panel-nothing (tech sheet not helpful). 110V at the control is present. What is the problem? What should I do and buy?
1 Answer Jerry, The flashing lights on the dishwasher indicate a stuck keypad and if turning off power to reset did not correct then you will need a new Control panel. Read More...
Steve April 11, 2013 for Model Number KUDP02CRBL0 Dishwasher will do nothing. Power supply good to machine but have no lights - nothing. Where do I start?
1 Answer Hello Steve. Based on the information you provided, it sounds like the thermal fuse W10258275 is bad and will need to be replaced on the unit. Read More...
Steve O. April 07, 2013 for Model Number Whirlpool gu3600 Sometimes fails to fill with water after prewash, though does fill and drain prewash water. Always sticks at 44 min during wash, any cycle, and will stay there indefinitely. will fill and drain normally on rinse only cycle. Control board?
1 Answer Hello Steve, This does sound like a control issue but you should also check the water heating circuit since this is the most common issue on these that stops the unit from advancing in its' cycle. If you would like more information, please re-post with the full model number and we can pull pertinent information particular to your unit and even provide the part numbers for it. Read More...
1 Answer Hello Mike. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jurgen March 22, 2013 for Model Number KUDP02CRBSO After a power outage dishwasher is dead. I replaced control board and user interface. Still not working Lights for ;light, china and rinse only coming up but no action lights for heavy duty and normal do not come up. Pressing cancel, cancel lights comes up it goes in drain mode and then nothing .What else need to be replaced?
1 Answer Hello Jurgen. You may need to replace the control panel WP8572354 or the interconnect WP8531873 on the unit. Read More...
Mark March 19, 2013 for Model Number Kenmore Elite Dishwasher 665 13863K602 Need to replace control board AP4309110. How are the existing orange/blue/yellow/brown wires going into the side of the control panel attached? Do you just pull out these wires? There is a flat wire assembly that attaches to one end of the control panel. How do you disconnect this flat wire wire from the control panel? Is it a pressed on connection? Any special tools required?
1 Answer Mark, This should be just a slide on connector for the orange/blue/yellow and brown wires and you would just pull them off. The ribbon harness will have a clip on it in order to disconnect it. Read More...
Clayton March 09, 2013 for Model Number GU2700XTSS1 Dishwasher had a blinking clean light. I ran the diagnostic normal-heated dry button sequence and it displays D3 and 07 and then completes about a 16 min cycle. I tried a regular wash after that and it gets stuck at 44 min and will not complete the cycle. What is the most likely cause and what parts do I need? Thank you
1 Answer Clayton, The Blinking clean light would indicate a faulty heating circuit. You will want to check the heater and check the thermistors. Check wiring back to the control board. If all this checks ok then you have a faulty heater drive on the control board. Read More...
Sloane February 24, 2013 for Model Number DU1055XTVQA My whirlpool quiet partner 2 dishwasher is only 14 months old(no warranty purchased) but has had many problems. The detergent cup doesn't open and it doesn't complete the washing cycle...just keeps running and running. A repair man came yesterday and tried running it several times and it ended up filling with sudsy bubbles even though we didn't put any detergent in. We have NEVER put dishwashing liquid in and always use a gel based product specifically for electronic dishwashers. These suds continued through over 20 cycles. I thought cleaning these suds out might fix the build up but the dw is stil not working. He said perhaps a new control panel is needed but with such a new dw, is there any other thing to trouble shoot beforre buying a part that is almost half the cost of the original dishwasher itself??
1 Answer Sloane, There's a few things to try before you replace anything. Fill the dishwasher, then add a couple of tablespoons of cooking oil,or powderred non dairy coffe creamer to the water and run the dishwasher for 5 or 10 minutes, then check for the suds,(you may have to repeat this process a few times, until the suds are gone. You'll then want to clean the dishwasher with products such as "Affresh" or "Glisten" W10501250 W10549845 to remove any chemical build up in/on the dishwasher components or tub, racks, etc. You then will want to remove the lower kickplate panel, find the tech data information sheet attache dto the back side and conduct the Service Diagnostic cycle. Running this test cycle will reset the control board and sensors back to factory settings, unless there is an issue with one of the sensors or control. If there are no issues once you've done all this, you may want to consider a different type or brand of detergent, and or review the owners manual for proper detergent usage. Read More...
Mike February 06, 2013 I have a whirlpool mod. GU2275XTVYO the clean light blinks seven times stops and blinks seven times. Im not getting any thing else.Any ideas?
1 Answer Hello Mike, The clean light blinking 7 times indicates a heater problem. Check your heater and wiring to heater to make sure that it is good. If bad correct issue and run diagnostics. This will allow unit to operate normally. Read More...
Dave January 21, 2013 for Model Number 72180833500 The control pannel has gone out. I can't see how long to cook, to defrost, etc. The microwave still works however. It has a 30 sec button and I can push it and hit start and the unit works. Does it need a control pannel and if so which one? If I order the wrong part can I return for the correct one?
1 Answer Hello Dave, The control board is the part that you would need since the unit has no display. The part number for control board is 6871W1S387B Read More...