Mike P November 28, 2011 for Model Number KitchenAid kudp02crbs2 The normal light and the cancel light blink at the same time when I try to start the machine. I have shut the power off and when I turn it back on it seems to drain for a few seconds and then shuts down. Do you think that the control board is bad! If I replace the board is there anything I should also replace as long as I have it apart?
1 Answer Hello Mike. Yes, based on the information, you will need to replace the control board WPW10084141 and the control panel WP8572354 if the buttons are not working properly. Hope this helps. Read More...
Siva October 12, 2011 for Model Number GU2455XTSS0 I don't see any open or smell on the board, but I ordered a board to replace from here. Let me get and update what happens. Thanks for the reply.
Conrad October 12, 2011 for Model Number AP 4309110 I recently replace the control panel AP4309110 and the thermal fuse w10258275, after conecting the power the only light the came on was the washing light all the other bottoms did not responded the machine sounded like like it was washing for like 2 minutes then it shut off, now the machine is all dead once again......what do you think it could be the problem thanks so much for the help and by the way your weeb page is great.
1 Answer Conrad, You need to check the door switch circuits, and the thermal fuseand wiring(again) . You most likely will need the control panel/keypad assembly, if everything checks OK. Thanks and Good Luck Read More...
Siva October 11, 2011 for Model Number GU2455XTSS0 No lights on the front, power to the board checked on, Fuse has continuity. Is this ECB problem? What Skill level needed for replacement?
1 Answer Hi Siva. Did you smell or see any opens in the board circuitry? Control board is part # WPW10084141. The Control panel is part WPW10008660for black. The stainless is part # WPW10008680. Inspect if the keypad is plugged into the board or see if the ribbon cable does not have any burnt spots. Thank you. Read More...
Chris September 04, 2011 for Model Number DU1055XTPB4 Dishwasher quiet no lights at all and it will not start. I'm thinking it's the control board what do you think?
1 Answer Hello Chris. You will need to test the thermal fuse W10258275. It is located on the control board. It should read closed for continuity. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Sanjay August 24, 2011 for Model Number DU1055XTSS Hi My dishwasher wont start. The "Start" button and "Cancel" button are not responding. The other buttons (such as wash cycle) are responding but the machine doesnt start. What should I do? Thanks
1 Answer Hello Sanjay. Make sure the door switches WP8269209 are good. If so, you will need to replace the control panel WPW10021710. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Don August 20, 2011 for Model Number DU1100XTPSA Cannot start dishwasher. The only button that lights up and appears to do something is the drain button. Do you think the electronic control panel needs to be replaced?
1 Answer Hi Don. You Will need the control panel. For white you will need part # WP3385735. For Black is part # WP3385734. For bisque is part # WP3385734. Thank you. Read More...
Charlie August 15, 2011 for Model Number Whirlpool GU3600XTSY2 My Whirlpool Quiet Partner IV Dishwasher does not start. The model number is GU3600XTSY2. After I discontined and reconnected the power to the dishwasher, the "Power Scour" light was blinking. And when I pressed "Cancel" or "Start" button, the "Power Scour" light stays blinking, "Pots & Pans" and "Normal" lights start blinking as well. Now three button lights are blinking. If you now press any buttons, no more response from the dishwasher, except the three blinking lights. Your helps are greatly appreciated. Charlie
1 Answer Hello Charlie. Check and make sure the door switches are good. If so, make sure the ribbon cable from the control panel to the control board is clean and dry. If so, you will need to replace the control panel WPW10021180. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Kb August 12, 2011 I just changed to a new control board and the Normal cycle time seems to be about 3 hours.
1 Answer Hello KB. That sounds correct. Cycle time is based on a number of factors in the cleaning cycle. How dirty the dishes are, the water temperature, and the options selected on the control board WPW10084141. Hope this helps. Read More...
Kenny August 12, 2011 for Model Number 665.13749k601 Getting power to circuit board. Power to right door switch but not to left ,no lights on control panel is this a board problem? Thanks
1 Answer Hi Kenny. Check with the connections at the junction box below behind the toe kick panel. The hot L-1 9blk) and the neutral (white)wire will both go to the door switches. If you have to replace one you should replace both because of age/usage issues. Then check to see if you get 120vac to both door common switch terminals. Then by closing the door latch you should get 120vac to the board. This board is part # WPW10084141. Thank you. Read More...