Michael December 23, 2017 for Model Number KUDS02FRSS1 Cycles do not complete on their own. During a cycle it will stop running, if I hit the upper right side where the control board is located it will run again. Is the control board the only part that is needed?
1 Answer Michael, This issue does sound likely that it would be caused by a faulty main control board. The control board should be the only thing needed. Read More...
Lawrence Ramirez October 30, 2017 for Model Number kenmore dishwasher 665 13842k601 Problem is no power. Reset main board by alternately pressing "sani rinse" and "heated dry" twice. All lights light up then "normal wash" and "washing" lights then "Quick rinse" and "drying" lights. Machine seems to run. This logic occurs twice then machine shuts off after several minutes.
1 Answer Lawrence, You pressed the wrong keys " To invoke the Diagnostics Cycle, perform the following key presses or actions in less than 6 seconds while in standby: Heated Dry ? Normal ? Heated Dry ? Normal . (To rapid advance one interval at a time, press the Start/Resume key). Invoking Service Diagnostics clears all status and last ran information from memory and restores defaults; It also forces the next cycle to be a sensor calibration cycle." If there is an issue with the control, certain lights will flash, at the end of the test mode. If there are no flashing LED lights at the end of the test mode, replace the control panel / key pad assembly. Read More...
Vince October 12, 2017 for Model Number kudso2frss1 I am confirming part nu control board mine 8562996 rel yours shows ap6014950
Joseph Lara August 08, 2017 for Model Number KUDS03STBL2 I am in the processing of replacing Control Panel Board along with thermal fuse cutot. When I removed all of the connectors I see the connector ribbon that connects to board has one less number of connectors than the board. Please confirm whether I align ribbon 1 with the second conductor on board so the tape is offset to the left side of connection. Can you send photo of what finished connection is look like?
1 Answer Joseph, The ribbon harness connector should have the same amount of terminals as the board and would slide on only one way. Read More...
Gina April 26, 2017 for Model Number kudt03ftpa3 i Cant tell if I already posted this question. Please help!! on my dishwasher I have 2 control panels. The electronic control panel and the touchpad control panel. I replaced the 1st one, but not repaired. I'm wanting to find out how I can tell if the panel control is bad. I previously got a blinking start button, and now the drain cycle will not even work. I tried the reset with scrub/heat buttons nothing. I see my part W10111537 is discontinued. Do you know of another panel I can use? how can I test if my panel is bad. I noticed there is a lot if info out there but its very hard to tell if they are referring to the electronic control panel or the touch pad control panel. How can I tell if it isn't the thermofuse or the door latch?
1 Answer Gina, We wish you had included an e mail address, we would've sent you some helpful information. If the problem was a thermal fuse or door latch assembly, there would be no power to the controls, and there would be no display lights at all. The control board WPW10084141 / W10084141 would be the least likely of the two components involved, and you should start control panel / console WPW10078133 / W10084183 but it is no longer available from the manufacturer. You can remove the lower kick plate panel and check to see if the tech data sheet is attached to the back side or it may be attached to the front frame and use it to conduct the diagnostics test and use the information for testing the key pad circuits. You disconnect the key pad ribbon from the control board, clean the end of the ribbon with rubbing alcohol or electrical contact cleaner, carefully clean the ribbon connector on the control board. give it a few minutes to evaporate then put it all back together and run the diagnostics test again. Read More...
Andrew K April 25, 2017 for Model Number KUDS03CTSS2 Our Kitchenaid dishwasher model KUDS03CTSS2 appears to work. The problem is that the rinse only, start, cancel and drying LEDs are dimly lit. Ran the diagnostic by pressing high temp wash, air dry, high temp wash, air dry and it completes with no issue. The dimly lit LEDs did happen about 1 year ago and eventually the problem disappeared, but now they are dimly lit again.
1 Answer Andrew, This issue sounds like it would be caused by a faulty control board on the unit. Read More...
Bill February 20, 2017 for Model Number Kenmore, 665.17032403 Dishwasher will not work. A few of the option lights come on but the lights for the wash cycles, timer and power do not. Main control board and/or thermal fuse? Control panel? Any assistance would be appreciated. Thanks, Bill
1 Answer Bill, This issue would most likely be caused by a faulty touch pad which you will need the control board. Read More...
Wayne C February 13, 2017 for Model Number KUDP02SRBL0 I sent a question earlier asking for advice about why my dishwasher has completely failed and smelled like it overheated. That was before I took the front panel off to have a look at the Thermal Fuse. I found that the circuit board was severely burned. It looks like it was actually on fire. The connector ends of some of the wiring harnesses that connected to the board were severely burned too. Does it make sense to replace the circuit bard, the wiring harness and the thermal fuse to repair this dishwasher? What else would I need to replace? What would cause such an electrical problem to begin with? Could there be a motor problem too that would lead to the electrical fire? I have had a several great experiences with Appliance Parts Pro for many of my appliance repair projects and appreciate your help and advice.
1 Answer Wayne, This issue could have been caused by a loose connection and would just need to replace the control board, harness and thermal fuse. Read More...
Fred C January 16, 2017 for Model Number gu3200xtpb4 Normal light blinks no response, before it quit some times water would"nt drain.
1 Answer Fred, The normal light flashing would indicate a faulty control panel which is part number WP3385741. Read More...
Jennifer January 08, 2017 for Model Number KUDI02IRBL1 I have replaced the electronic control board in my dishwasher (KUDI02IRBL1). Went to put the DW back together and cannot find the protective cover that goes back over the control board. It is not shown on the parts diagrams for my model. Do you have anyway of finding a part number for that cover?
1 Answer Jennifer, Unfortunately the cover is not showing as being a part that would be available to purchase on this unit. Read More...