Lorenzo T June 02, 2015 for Model Number DU1055XTSS3 Hello I have a question about my dishwasher, it gets lock and I do not how to unlock.
1 Answer Hello Lorenzo. To turn on Lock: Press and hold Heat Dry for at least 4 seconds. The Locked light glows. If you press any pad while your dishwasher is locked, the light flashes 3 times. To turn off Lock: Press and hold Heat Dry for at least 4 seconds. The Control Lock light turns off. Read More...
Jb May 29, 2015 for Model Number GU2700XTSB1 Had a power outage several days ago. Dishwasher starts and all buttons seem to work properly. I noticed last night that it was taking longer than normal to wash dishes. It appears the cycle started, water heated up etc., yet the timer is not counting down and it seems to stay "stuck" after it runs for a while. (e.g. last night i watched for approximately 10 minutes and it stayed at 40 minutes and never counted down). This morning tried again and it started normal, yet it seemed to "stick" at 60 minutes and never count down. I do notice when starting initially that where the countdown minutes are displayed it displays flashes going counter clockwise for several minutes before it starts. Could the electronic control board have gotten fried with the power outage?
1 Answer Hello JB. It sounds like the control board may have been damaged and will need to be replaced on the unit. Read More...
Phillip April 26, 2015 for Model Number KUDK03ITWH0 Console light stays on. Cancel button doesn't work. I can not turn the dishwasher off and pressing any button, I get no responses. Thanks
1 Answer Hello Phillip, If you have a light on all the time, not flashing, you most likely have a bad touchpad WPW10078106. It is also possible to have an issue with the control board WPW10084141. Read More...
Attila March 17, 2015 for Model Number KUDA03CTBS3 Hi my dishwasher is not doing anything. I checked the thermal fuse is good so looks like a control panel. Would you agree? I even checked the door switch to. And another question I was able to disconect some of the connections but one really did not want to come off. Is it some kind of trick to disconnect them all?
1 Answer Attila, The issue with the unit not starting and the door switch and thermal fuse checking ok would most likely be the control board. You will want to check the power supply where it comes into the unit to make sure that there is a good firm connection and also check to make sure that there is 120 vac at this point. Read More...
Jordan February 14, 2015 for Model Number W10084141 Board I have a kitchenaid dishwasher. Twice now I have replaced the control board and dispenser. Same issue both times. The transistor controlling the load to the dispenser solenoid has faulted. The 120v load then gets a free pass through the transistor and burns out the solenoid. My question is why? Is there a manufacturing flaw with the board? This is an expensive replacement (destroys dispenser and board). Please help.
1 Answer Jordan, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Diane January 31, 2015 for Model Number GU2455XTSS2 Whirlpool Dishwasher MODEL GU2455XTSS2 SYMPTOMS: - Front panel lights flash in irregular patterns, most frequent patter is Pots&Pans and Normal buttons paired with left and "- -" shows on Time display. Intermittently, blinking items change with no user action. - The Cancel button sometimes clears the panel lights for a few minutes, then some start blinking again. - Blinking sequence is regular (not patterned). - Unplug/replug does not correct the problem. - QUESTION: Will replacing the Control Panel or the Control Board fix my problem? or another part?
1 Answer Diane, The flashing keys is representative of a faulty control panel. The keypad on the control panel has stuck keys which is causing this issue. The part number for the control panel is WPW10008660. Read More...
Dennis January 28, 2015 for Model Number kudp02crbti Wash cycle keeps running will not cycle to next setting.
1 Answer Hello Dennis. It sounds like the control board WPW10084141 is bad and will need to be replaced on the unit. Read More...
Lar January 19, 2015 for Model Number KUDI02CRBS0 Our dishwasher control lights are out. I have verified power to the unit, verified voltage in/out of the thermal fuse, verified power to the door switch and out when the switch is engaged. We have also disconnected the control panel to ensure clean connections/pins. We attempted to run the control diagnostics by disconnecting the button control panel per the manufacture diagnostic instructions and not luck. Does this sound like a failed controller board? The controller board P/N is 8559825. Thanks, Larry
1 Answer Hello Lar. Yes, it sounds like the board WPW10084141 may be bad and need to be replaced on the unit since the fuse is good. Read More...
Gregg December 22, 2014 for Model Number Whirlpool DU100XTPQ8 Have flashing control panel lights. In checking your message board, it appears to be the control panel. Is there any way to guarantee this is the problem before I order that part?
1 Answer Hello Gregg. If the lights flash, but the start button does not work, the first thing you check is the door switches. If they are good, then the control panel is bad. The ribbon cable can be tested for continuity when pressing the start button. Read More...
Flora December 17, 2014 for Model Number Whirlpool GU3200XTPQ5 I have different problems with the dishwasher. The Time Remaining display sometimes shows changing times e.g. 1H, 4H, 7H etc and then it stops. When I press Cancel, sometimes the machine will drain, other times nothing happens. The Normal light blinks continuously and pressing Cancel does not do anything. I have tried resetting the control panel by shutting off the power for about 15 min. and pressing Pots & Pans - Heated Dry - Cancel about 2 - 3 times. The control panel was cleared, but when I pressed Normal, the light started blinking again. I left the machine alone for a few hours and noticed that the Start light was blinking continuously, so I pressed Start and the machine completed a wash cycle. I have not been able to repeat this with any success. Do I need to replace a part(s)? Thank you
1 Answer Hello Flora. You need to replace the control panel. If the issue continues, you will need to replace the board on the unit. Read More...