Ben March 19, 2014 for Model Number MDBTT53AWW1 I have a maytag dishwasher that was running on a normal wash cycle with heated dry and upon returning to unload dishwasher the delay hours button was blinking. When I go to press any other buttons the normal wash and heavy wash buttons light up but no response. I have tried to reset power at breaker with no such luck. Wondering if it is the actual circuit board inside or the face panel with the buttons actually on it
1 Answer Hello Ben. You will first check the door switches on the unit and make sure they are good. If they are good, then it sounds like the control panel will need to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Terry March 17, 2014 for Model Number 110.21102011 This washing machine is not stopping filling and over flows the water over the top of tub. It has worked fine since new. Is this a computer stopping water (at hight or weight) issue? Need a new computer board? Any help will be appreciated.
1 Answer Hello Terry. It sounds like a problem with the water level switch. Inspect the hose to the switch if in good shape replace the switch part# WPW10268912 Read More...
1 Answer Hello Harry, If the control is sending voltage to the dispenser properly, the dispense assembly WP8558129 will have to be replaced. Read More...
Adrian March 13, 2014 for Model Number GU3200xtxy4 Nothing lights on the control panel. I checked the power and breaker and it all works. Do I replace the circuit board?
1 Answer Hello Adrian. You need to check the thermal fuse and see if it needs to be replaced on the unit. Read More...
Gary March 10, 2014 for Model Number GU2275XTVYO Middle light that has the word clean keeps flashing and the other buttons light when u push them but then they go off and it flashes again
1 Answer Gary, With the clean light flashing 7 times then pausing then you would have a issue with the heating circuit. If the light just continues to flash without a pause would be a control panel problem. The heating circuit issue you will want to check at the main control board when the unit is on and when the heater is supposed to be on to see if there is 120 vac going to the heater. If there is not then replace the control board. If not then test the heater and thermostat. Read More...
1 Answer Hello Erika. Yes Part# WPW10084142 is the correct control board for your model. At this time the part is on a vendor back order. According to the manufacturer it should be available the first of March. Read More...
Absolut February 25, 2014 for Model Number mdbh949aww1 Control buttons light up but dw wont start sounds like a relay clicking and lights flash on and off, control bad?
1 Answer Hello. If the start button works, but the board does not power the motor, you will need to replace the control board on the unit. Read More...
Julie February 08, 2014 for Model Number 66513893K801 I'm not clear on what I need to replace. My dishwasher start button does not go on when pressed. The normal wash button lights up and the heated dry button goes on, but the start does not light up and when I close the door it does not start. So, the start button is not working. What do I need to replace? Maybe the control panel? Thanks.
1 Answer Julie, If all the lights are displaying but the unit will not start when the start button is pushed then you will want to check the door latch assembly to make sure that the switches are closing to allow the unit to start. If the latch is not making then the unit will light up but will not start. Read More...
Sam January 21, 2014 for Model Number du1055xtv81 When we run dishwasher it never gets out of washing mode. Do you have any idea which board this might be? Thank you for any help
Ken January 10, 2014 for Model Number MDB4709AWS1 The dishwasher is about 2 2/5 years old. For some time the start button was hard to activate. Now it doesn't work at all. When I reset (normal and heated dry rapidly) the normal light comes on and the start light comes on and the washer starts. It cycles between wash, rinse and wash. Runs about 45 minutes and there are no lights indicating that it has finished cleaning. Thanks Control Board Number W10285180B
1 Answer Hello Ken. Based on the information you provided, the control panel W10810390 is bad and will need to be replaced in the unit. Read More...