Wayne H. April 22, 2012 for Model Number 66515979992 The buttons on the control panel are dim. The buttons are normal wash, heating, rinsing, drying, and lock. I am being told the control panel is bad. The model # is 66515979992 and the serial # is FJ4705251. Is the control board you have listed the one I need? Item Number: AP3175633.
1 Answer Hello Wayne! Yes, the control board WP8530929 is the correct replacement part used on your Kenmore model 665.15979992. The control panel in all colors except for black have been discontinued, for the black panel use part number WP9744497. Thanks! Read More...
Marcia February 15, 2012 for Model Number gu980scgt3 control board If our dishwasher just keeps runng over an over is this the part we need or do we need the control touch panel?
1 Answer Hello Marcia. Yes, you will need to replace the control board WP8530929 if the unit does not shut off and keeps running. Hope this helps. Read More...
Rick F. December 27, 2011 for Model Number 66515639000 Having a problem with my Kenmore dishwasher model 665 it will not go to a wash cycle the quick wash light just keeps on blinking and I cant clear it with the cancel butter nothing works. Just before this the cancel light was blinking and the pots and pans light was blinking also.
1 Answer Hello Rick. Based on the information you provided, it sounds like the control panel WP3384470 is bad and will need to be replaced. Hope this helps. Read More...
Fuzzzzy December 26, 2011 for Model Number 665153900 The quick wash and the cancel light are blinking but nothing happens I open the door and all the lights go off then I push the start button the light start to blink and agan nothing happens. Once every so often the washer works and it washes fine it’s just getting it to start
1 Answer Fuzzzzy, You want to replace the control panel/keypad assembly. "WON’T RUN AND LED ABOVE KEY(S) IS BLINKING a) Stuck key(s) or shorted circuit(s) in keypad Check keypad. b) Shorted circuits or connections on the control that read the keys. Check control. You'll also need to reset the control : If the key sequence is entered with the dishwasher in Standby, the Diagnostics Cycle is started. The Diagnostics Cycle can be rapid-advanced, interval by interval, by pressing the Pots&Pans/Heavy or Anti-Bacteria/Cookware cycle key. HIGH TEMP SCRUB, AIR DRY,HIGH TEMP SCRUB,AIR DRY or SANI RINSE, NO HEAT DRY,SANI RINSE,NO HEAT DRY. Thanks and Good Luck Read More...
Jack November 29, 2011 for Model Number 665.17777990 The lock on light is on blinking. I tried to turn off it wont. I tried power off for half hr nothing. I took panel off unplugged board worked for two cylces then same tried again and nothing.
1 Answer Hi Jack. It seems like the keypad console is not responding. Part # WP3384340. Thank You. Read More...
James October 14, 2011 for Model Number 66515869990 Replaced. Mother board only light on quick wash blinks nothing works.
1 Answer Hello James. Make sure the door switches are good. If so, you have a bad control panel 3384237. This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Thanks. Read More...
Paul October 05, 2011 for Model Number 665.15784300 Hi, You only answered one of my questions, I also asked "could the new pump/motor be defective and cause a short in the controller board?"
1 Answer Hello Paul. No, the pump should not cause the control board to short out. If the original problem was the pump, and the board was working fine, there could be a wiring issue, but the pump shouldn't short out the control board. Thanks. Read More...
Paul October 04, 2011 for Model Number 665.15784300 I just replaced the seals then the entire pump/motor assembly. The unit worked like new for exactly one time. Now the "lock on" light stays on and can't be reset. Could the new pump be defective a cause a short in the controller board?I see the cost for the controller just went up about $30. If I replace this , I will be approaching the cost for a new unit! Please help!
1 Answer Hello Paul. Check and make sure there are no loose connections and the ribbon cable is seated properly. If so, and the control panel is good, it sounds like the control assembly WP8530929 is bad and will need to be replaced. Hope this helps. Read More...
Steve G. September 28, 2011 for Model Number KUDM25SHWHO I have a Kitchen Aid dishwasher made ny Whirlpool. My child lock would not go off so I looked for answers and found out that the control board might need to be replaced. I took out the control board so I could match it up to the pictures on this web site. It was out for the afternoon. When I put it back in it worked great. The electrical connections looked clean and the overall condition looked non-corrosive. My question is, will I eventually need to replace the control board?
1 Answer Hello Steve. You may have had a bad connection on the ribbon cable. If it happens again, you will need to replace the control panel WP9744106 on the unit. Hope this helps. Read More...
Karl August 17, 2011 for Model Number kudr25hbl1 How would I determine for sure to change AP3175633 or AP2921033 (console or board). Lights on selected cycle and options are lit,but once you press start button they turn off. Pressing again start button goes in cancel mode and drain cycle starts. Playing with ribbon cable sometimes start cycle. Is any way to start cycle(normal,soak/scrub etc.) if AP3175633 is bad? Thank you very much
1 Answer Hi Karl. If You are giving it a command and it don't follow through, then it is the control board. Part # WP9744109. But in order to verify you need to remove the bottom kick panel and use the tech data sheet to put the unit in a test mode to check for further errors. Thank you. Read More...