Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Range Bake Heating Element by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18055272
Manufacturer Part Number: WPW10276482

Oven not heating or heating slowly? Your bake element likely failed. Located at the bottom of the oven cavity, this part restores even baking. Easy DIY fix.

More
$125.63

IN STOCK
Ships Monday Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Range Bake Heating Element (Part Number: OEM18055272)

1 Answer

Sally, it would not be recommended to plug the stove back in with the element wires not secured properly as this is a safety hazard. If the original element is not grounded out and is just not heating, it would be recommended that the bad element be re-installed before plugging the stove in. This will eliminate the chance that the terminals touch bare metal and cause a safety issue.

Read More...

1 Answer

Hello Jake, you'll want to test for voltage at the bake and broil element also make sure they both are coming on. If not, you'll want to replace the defective element as long as voltage is present. Thanks!

Read More...
Sandy for Model Number MER8772WS0

When selecting Bake on our Matag MER8772WS0 electric oven it will heat and get to temp. pretty quick and then post a fault detected, press start to try again. I noticed the broil element is on and glowing red all the time. We have tried unplugging for 3 minutes, then plug in and set clock and still happens. I removed the bottom oven cover that sits over the bake element and then set the oven to bake, it start and the bake element never glows, but the broil element glows the entire time. The user manual says "The bake and broil elements cycle on and off in intervals. The bake element will glow red when cycling on; the broil element will not. This feature is automatically activated when the oven is in use." I am thinking most likely the issue is the bake element, once it cools I will remove and ohm out with a meter. If it does not show open, could it be the Oven Temp sensor, or would you suspect the control board

1 Answer

Sandy,

If the element checks ok then this will most likely be an issue with the control board of the unit.

Read More...

1 Answer

Jack,

You will want to make sure that the arms of the hinge are locked in place at a 45 degree angle. You will then slide each side of the door into the receivers and the hinges should slide into a groove. Once into the groove you will rotate the hook on the hinge down and the door should be in place.

Read More...

1 Answer

Bill,

To access the bottom element you will need to pull the unit out from installation and remove the rear cover. This will allow access to the bake element. The things that you will want to look at would be the element, the thermal overload and possibly a bad control board.

Read More...

1 Answer

Hello Adam,
You should check for 120Vac testing with a voltmeter from terminal P5-5 to terminal P5-8. If this isn't present, the safety thermostat 318004900 could be open. This safety thermostat has a reset button on it that has to be pressed and wiggled a bit to reset. The power has to be off to do this since 120Vac rides on one side even if it is open. If it is closed, 120Vac is on both sides. If the voltage is there, the electronic oven control 316418720 has failed.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google