Lorrain September 15, 2014 for Model Number JSD2690HES I need to purchase the Housing unit for the water filter. Mine is leaking. Please advise apart number or how to purchase this. Thank you, Lorrain
1 Answer Lorrain the filter cover is part number WP12568001, backing plate is part number 12688503, and the water filter head assembly is part number WP67004106. Thanks! Read More...
Wayne August 30, 2014 for Model Number KSRB250GBL01 Does this model fridge(kitchen aid) have a water filter?
1 Answer Hello Wayne. This unit does not come with pre installed water filter, you will have to an a inline water filter part number 4378411RB to filter the water before it enters the fridge. Thanks! Read More...
Patricia August 13, 2014 I cannot get a new water filter to turn after I get it in (it is a Whirlpool Gold - filter in the grill at the bottom). I replaced it before, but now cannot get the filter to turn and lock into place. Any solution?
1 Answer Hello Patricia. If the filter will not lock into place, you will need to replace the housing on the unit. Read More...
David August 07, 2014 for Model Number 106.72159110 I need help locating the water filter for my Kenmore Coldspot?
Sharon July 19, 2014 for Model Number KFCS22EVMS0 How do I replace the filter head inside the filter cover.
1 Answer Sharon, To replace the filter head, you will first need to pull out the unit and turn off the water supply. Disconnect the tubing that goes from the filter to the water valve and water supply lines. You will then remove the plate over the filter lines where they enter the cabinet. Go to the front of the unit and lower the cover of the filter and where it is hinged just pull to one side to release the cover and slide the opposite direction to remove the cover. Once this is done, the filter head is held in by clips that you would just pull the head out of the clips and pull the tubing and all out of the refrigerator and install the new one. Assemble in reverse. Read More...
Hcakelady July 18, 2014 for Model Number GB2FHDXWQ01 I've looked all over and can't find the filter. Not on the back, kickplate or fresh compartment. Does it have a replaceable filter?
1 Answer Hello, according to the use and care guide for this model number if it has a water filter is located in the upper right hand corner of the fresh food compartment. It uses water filter EDR4RXD1, thanks! Read More...
Caridad M. June 14, 2014 for Model Number MFI2569YEM2 How can I change the filter? Where can I find it?
1 Answer Caridad, the filter is part number EDR4RXD1. The filter is located in the refrigerator section. Here are the instructions from the user manual supplied for your model. Thanks. 1. Turn filter counterclockwise to remove. 2. Remove sealing label from replacement filter and insert the filter end into the filter head. 3. Turn the filter clockwise until it stops. Snap the filter cover closed. 4. Flush the water system. See “Water Dispenser” or “Water and Ice Dispenser.” Read More...
Marci April 10, 2014 for Model Number GS6SHEXNB-BOB BLACK I have a 2005 side by side black whirlpool conquest refrigerater. Model# gs6shexnb-bob b . I need a water filter in black. This placement is to be put on bottom of refrigerator. Can you tell me where i can get this? Thank you.
1 Answer Marci, I believe your model should read GS6SHEXNB03. The water filter listed for your model is part number EDR5RXD1. If you need the filter cap use part number WP2186494B. Thanks! Read More...
Brian G April 05, 2014 for Model Number KFCS22EVMS0 We replaced our original water filter about a year ago. About one week after replacing it when we tried to use the water dispenser, a loud knocking would occur and very little water came out. We purchased another filter believing the first was defective and it happened again. When we remove the filter and put the plug cap on the knocking does nor occur.The filter we purchased is part # UKF8001. Is the knocking caused by the filter or is the inlet valve possibly bad?
1 Answer Brain, In most cases when the filter gets turned in and the unit is making the knocking noise, it is because the filter did not get turned in fully and is not hitting the pins that allow the water to flow properly. When you get the filter turned in and it seems to stop then try to turn a little more and if it turns more then try the water and see if the knocking noise is still present. If not then the filter just was not in all the way and if it does continue to knock then the filter head would be the issue. Read More...
Bill March 12, 2014 for Model Number MFD2561HEB I need to replace my filter. It looks like I should use the filter UKF8001, however the filter currently in use is the 4396395. Does it matter which filter I use?
1 Answer Hello Bill. On your model you can use either filter. The only difference in the filters is part# EDR4RXD1 has the MayTag logo on it. Read More...