John November 13, 2018 for Model Number GEW9200LW0 my model gew9200lwo dryer keeps shuting down with an e1 code coming up. Need to keep turning it back on to finish drying close. Heat seems to be hot enough. Cleaned all the vents very well and still does it. Thanks for the help
1 Answer John, you need to replace the thermistor, part number is WP8577274, it is located by the thermal fuse on the blower housing. Read More...
Lemuel October 20, 2018 I have a Whirlpool Duet GEW9200LW1it runs but no heat. The heating element was just changed a few months ago. How do I verify? Thank you
1 Answer Lemuel, You will want to test the thermostats in the unit and check to make sure that the venting of the unit is clean. There are 2 components other than the thermostats which would cause the heating element not to work. First is the motor and second the Control board. The best option is to disconnect the power to the unit and access the heating element. Disconnect one wire that is going to the heating element, preferably the one on the thermostat side. Plug the unit back up and using a multimeter you will want to turn the dryer on and test for 120 vac at the terminal on the heater where the wire was disconnected. What this will do is eliminate the heater element itself and the motor. If there is 120 vac at this point then you know the heater is good and the motor is good because the other 120 vac coming through the thermostats is the control board side of the circuit. If there is not 120 vac at that point then you will want to test the other terminal on the heater and check for 120 vac. If there is not 120 vac then the motor would be bad . Read More...
Tom July 02, 2018 for Model Number LEQ8611PWO Our dryer gets warm but takes a very long time to dry clothes. We have cleaned out the lint from the hose and outlet but it didn't get any better. Can the element be partially burned out? I haven't taken it apart yet but read it could be a couple of items.
1 Answer Hello Tom, First, make sure there are no seals missing from inside the unit and that the heating element WP3387747 is not shorted to ground. Read More...
Michael T March 19, 2018 for Model Number 110.29822800 My washer has quit dispensing the fabric softener when it washes. Do you have any suggestions as to what the problem could be? Thanks, Michael
1 Answer Michael, For this issue the most likely cause would be that the tub is not spinning fast enough. This issue would most likely be that the clutch is faulty or the brake is not releasing properly to allow spinning. The clutch would be the most likely cause. Read More...
Chris November 16, 2017 for Model Number MEDZ600TW2 My dryer is not heating when running a cycle (dryer tumbles but no heat). I presume it is in need of a heating element? Also, do you have a video showing how to replace? Your video on replacing the tub seal for a washer was excellent and made that replacement/repair easy!
1 Answer Hello Chris, Yo\u will need to order WP3387747 for the model provided. I'm sorry but we have not got a video on this Kemnore. Read More...
1 Answer Hello Mark. Here is a link to our warranty page. Thank you. http://www.appliancepartspros.com/customerservice/warranty.aspx Read More...
Don October 19, 2017 for Model Number Medx500xw1 The dryer keeps tripping the breaker. It takes several times resetting the breaker to get the load to dry.
1 Answer Hello Don. Try replacing the breaker. Many times breakers become weak and trip prematurely. If that does not work, then you will need to look for a heavy amp draw or a shorted out part. Thanks. Read More...
Mary October 19, 2017 for Model Number 11084821300 Lights comes on automatic temperature control panel but when I press start button only beeps nothing comes on will not start, Did replace thermal fuse still did not start.
1 Answer Mary, If you replaced the thermal fuse on the blower housing WP3392519 / WP3392519, then check the wires between the belt/idler switch and the motor(blue wires). If all's OK suspect the machine control board WP8546219 / WP8546219 has failed and is not supplying power to the motor to start and run it. Read More...
Rick September 05, 2017 for Model Number 11068732700 I am attempting to check out my heating element. All the videos I watched, techs removed the back of the dryer. However, on this model it seems that the entire back panel cannot be removed. do I have to go in thru the front? Sears/Kenmore Thanks, Rick
1 Answer Hello Rick. To replace your element, you will release the clips on the top of the toe panel on the front of the unit and remove the toe panel to access and replace the element. Thank you. Read More...
Barry August 29, 2017 for Model Number WED5700AC1 I am thinking of ordering your p/n AP6008281, a replacement heating element for a Whirlpool electric dryer. Are there any other associated parts that I should replace at the same time? Thank you.
1 Answer Hello Barry. Only if any of the other parts have failed. Otherwise, you just need the element. Read More...