Whirlpool Dryer Heating Element

Restore full heat and end long dry cycles - install the Whirlpool OEM Dryer Heating Element.

Why this heating element?

• Factory-spec 5400 W / 240 V heating element with nickel-chromium coil - built by Whirlpool to Whirlpool OEM standards.
• Broad compatibility: fits Whirlpool, Kenmore 110-series, Roper, Estate, Amana, Maytag & more 27-inch dryers.
• Built to last: high-temp terminals & mica insulation resist fatigue and hotspots.

Fixes these common dryer problems

DIY install — about 20 minutes

1. Unplug dryer and remove back panel to access heater housing.
2. Disconnect wires; remove housing screws and slide assembly out.
3. Swap old element for new, re-use hi-limit thermostat if still good.
4. Re-assemble, run test cycle - enjoy fast, even drying.

The Dryer Heating Element is an OEM replacement part for Whirlpool dryers. It is responsible for generating the heat necessary for the drying process, ensuring clothes and fabrics are thoroughly dried.

Symptoms of a bad dryer heating element include:

• Clothes coming out damp or taking excessive time to dry
• No heat or insufficient heat produced during the drying cycle  
• Visible signs of damage or burnout on the heating element itself
• Unusual burning smells emanating from the dryer

Causes of a faulty heating element can include normal wear over time, electrical issues, or physical damage from impact or overloading.  

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

The Dryer Heating Element is an OEM part for Whirlpool electric dryers. This element provides critical heat to properly dry wet laundry loads. Consistent warmth throughout cycles is key to leaving clothes completely dry. This 5400-watt, 240-volt heating element heats the air circulating around the drum.

Causes of a bad heating element can include failure due to extended usage cycles over time, or mineral buildup inhibiting heat transfer. 

Symptoms of a faulty element include:

• Inability to reach or maintain desired drying temperature
• Wet or damp clothes after full cycles   
• Potential safety issues if element overheats
• Dryer not working or requiring excess cycles to dry

This OEM Whirlpool replacement element is also compatible with Kenmore, Maytag, Amana and Whirlpool brands.

The Dryer Heating Element is an OEM part for Whirlpool dryers. This component is responsible for generating the heat needed to dry clothes efficiently. Situated in the rear or bottom of the dryer, the heating element heats the air before it enters the dryer drum, providing the warmth necessary for drying garments.

Common causes include overheating due to restricted airflow from a clogged vent, a break in the heating coil from wear and tear, or electrical issues such as short circuits. It's crucial to maintain proper dryer venting to prevent overheating and to ensure the longevity of the heating element.

Symptoms of a bad Dryer Heating Element include:

• Clothes taking longer than usual to dry
• Dryer not heating up at all
• Increased energy bills due to the dryer running longer
• A noticeable difference in drying efficiency

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

No longer includes terminals and adapter leads. You can purchase the wire separate, part number 279457. Another common Whirlpool dryer element is 279838. Use our model number search to be sure you're getting the correct element for your dryer.

The Heater Assembly Complete is an OEM part for Whirlpool dryers, engineered to generate and maintain the heat necessary for drying clothes efficiently and uniformly. This assembly ensures that your dryer can reach and regulate the desired temperatures without overheating. 

Causes of a bad Heater Assembly can stem from normal wear and tear, overloading of the dryer, insufficient maintenance leading to buildup and blockages, or electrical surges that damage the heating components. 

Symptoms of a bad Heater Assembly Complete include:

• Clothes taking longer to dry or not drying at all
• The dryer not heating up despite running
• Overheating of the dryer, which could trip safety switches or fuses
• Unusual noises or smells indicating potential electrical issues or burning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Heating Element is an OEM component specifically designed for Whirlpool brand electric dryers. It contains coils that produce hot air used throughout drying cycles.

Symptoms of a failing heating element include:  

• Slow drying times as clothing takes longer than usual to dry fully
• Excess condensation inside the dryer drum
• Damp items after an entire cycle 

Potential causes involve typical coil wear from repeated heating and cooling over many years. Mineral scale buildup or poor ventilation can diminish heating efficiency as well.

Compatible models include some brands produced by KitchenAid, Maytag, Amana, and Kenmore.

The Heating Element is an OEM replacement part for Whirlpool residential clothes dryers. The element plays a vital role in generating the necessary heat to effectively dry wet clothes during tumble cycles. Its high-wattage electric coils rapidly heat the circulating air.

Symptoms of a faulty heating element include: 

• Inability to achieve desired dryer temperatures
• Much longer dry times or inability to fully dry loads  
• Potential safety issues like arcing or sparking 
• No heat while drying

Common causes of failure are coil burnout from continuous use or damage from foreign debris inside the drum. Over time, being subjected to direct heat can deteriorate wiring insulation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and Roper clothes dryers.

The Heating Element is an OEM part for Whirlpool dryers. This part generates the heat necessary to dry clothes during the drying cycle. The element is designed to heat up when electricity passes through it, producing the warmth required to effectively dry laundry.

Causes of a bad heating element include wear and tear over time, electrical issues such as short circuits or power surges, and physical damage from overloading the dryer or mishandling the appliance.

Symptoms of a bad heating element include:

• The dryer not producing heat
• Clothes taking longer to dry than usual
• The dryer overheating or shutting off mid-cycle
• Unusual noises or burning smells during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Surface Element is an OEM part for Whirlpool ranges. This part provides heat to the cooking surface, allowing for the preparation of food. 

Common causes of a bad surface element include electrical faults, physical damage from heavy cookware, or degradation from constant heating and cooling cycles.

Symptoms of a bad surface element include:

• Inconsistent or uneven heating
• The element not heating up at all
• Visible damage such as burns or breaks in the coil
• Sparking or unusual noises when the element is turned on

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement heating element restores proper water temperature and drying performance in your dishwasher. It helps dissolve detergent, sanitize, and dry dishes at the end of the cycle for consistent, reliable cleaning results.

• Heats wash water and boosts final rinse temperature to aid drying
• Common failure symptoms: dishes not drying, detergent not fully dissolving, cycles running long, or lukewarm water
• Helps resolve poor cleaning and milky/white residue linked to low water temperature

• Disconnect power at the breaker and shut off water supply before servicing
• Access from underneath; remove toe panel/kick plate as needed and note wiring/terminal orientation
• Inspect and reuse existing seals/hardware if applicable; check for leaks after reassembly
• After install, run a test cycle to ensure proper heating and drying

This dual heating element fits select electric dryers. It generates the heat required for drying and supports variable heat levels on compatible cycles. Replace a failed element to restore proper temperature and consistent drying performance. What it does:

• Produces heat inside the heater housing; dual-circuit design enables multiple heat outputs on certain cycles
• Typical failure symptoms: no heat, low heat/long dry times, clothes remain damp after a cycle
• A shorted coil can trip safety cutoffs; restricted airflow can contribute to repeat failures

• 1 dual heating element

• Disconnect power before servicing and allow the dryer to cool completely
• Access location varies by model; note wire locations and hardware before removal
• Handle the element carefully to avoid damaging coils; transfer any reusable brackets/hardware from the original part
• Clean the lint path and external venting; correct airflow issues to prevent repeat failures

This is a dual radiant surface element for compatible glass-ceramic ranges and cooktops. It restores responsive, even heating and lets you choose a smaller inner ring or the full element to match your pan size. What it does:

• Converts electrical energy into radiant heat for the cooking zone
• Dual circuits provide selectable inner-only or full-size heating
• Helps resolve a burner that won't heat or heats only on one ring
• Addresses uneven or intermittent heat and visible hot spots or breaks in the element

• 1 dual radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool before servicing
• Access the element per your model's service procedure; note wire locations before removal
• Handle the element carefully and transfer any mounting brackets/insulators from the original
• After installation, test both inner and outer heat settings for proper operation

This genuine heating element restores consistent, controlled heat so your appliance can reach and maintain the proper temperature. Replacing a failed element can resolve no-heat or weak-heat issues and bring performance back to normal.

• Converts electrical energy into heat when powered by the control
• Helps the unit achieve and hold the set temperature during operation
• Typical failure symptoms: no heat, slow or uneven heating, cycles that take longer than normal, visible damage to the element
• May trigger heat-related error codes when failing

• Disconnect power at the breaker or unplug the appliance before servicing; allow all components to cool completely
• Note wire locations and terminal orientation before removal; transfer any mounting hardware from the original if needed
• Avoid bending or striking the element; handle by the bracket/insulators
• After installation, run a test cycle to check for secure connections

This replacement heating element restores proper heat in electric dryers designed with two-level heat. It generates the controlled heat needed for both high and low temperature cycles, helping return normal drying performance.

• Heats the air passing through the drum during drying cycles
• Supports two-level heat so high and low temperature settings work correctly
• Typical symptoms include: no heat, insufficient heat, longer-than-normal dry times, or only one heat setting working
• A visibly broken coil or an open reading on a continuity test indicates failure

• Disconnect power before servicing; dryer circuits carry high voltage
• Handle the element carefully—coils and insulators are fragile; do not stretch or deform the coil
• Note wire locations and ensure tight, clean connections during reassembly
• Clear lint and verify airflow; restricted ventilation or failed thermostats/cutoffs can lead to repeat element failure

This heating element generates the heat your electric dryer needs to dry laundry. Replacing a failed element restores consistent temperatures and helps resolve no-heat or long dry-time issues.

• Converts electrical energy into heat inside the dryer's heater assembly
• Typical symptoms of failure: runs but no heat, takes too long to dry, or clothes remain damp
• Visual clues can include a broken/burned coil or an open-circuit continuity test
• Restores proper drying performance when the original element has burned out

• Disconnect power before servicing; heating components operate at high voltage
• Access the heater assembly; note wiring and component positions for reassembly
• Handle the element carefully to avoid stretching or deforming the coil
• After replacement, clean the exhaust duct and check related thermostats/thermal cutoffs for continuity if heat issues persist

This bake heating element replaces the oven's primary heating element to restore consistent bake performance and even oven temperatures. Designed to heat quickly and quietly for reliable cooking results. What it does:

• Heats the oven cavity for baking and general cooking cycles
• Replaces a cracked, visibly burned, or non-heating element
• Helps restore oven temperature recovery and cooking consistency
• Stops symptoms like no heat, weak heat, or uneven browning

• Disconnect power at the breaker before servicing the oven
• Remove the oven racks and access the element from inside the oven
• Secure mounting screws and electrical connectors firmly; avoid overtightening