John G. March 22, 2012 for Model Number LTG5243DQ3 The Idler pulley does not have a wheel and rubs against curved metal. Is this one a upgrade? Also, when I checked the rear drum rollers they seem not to wobble and they moved freely on the shaft.Does the rubber wear down and if so is that the cause of a minor thumping sound? Thank you for your advice. John
1 Answer Hello John, The idler with a glide instead of a wheel was an attempt for Whirlpool to cut manufacturing costs and turned out to be a rework. The glides wear belts out prematurely and have to be replaced with an idler wheel assembly WP691366. I strongly recommend replacing the belt so you won't have to go through a tear down again soon to replace the belt 341241. The thumping noise is caused by the wheels 349241T wearing unevenly. Changing them would also avoid a repeat tear down. Read More...
Lori February 26, 2012 for Model Number RED4440VQ1 I have a 09 Roper Elecric Dryer and I would like to know how to put a belt on the drum and the pully.
1 Answer Hello Lori! Here is a link from our free repair forum with a diagram on how to install dryer belts. Hope this helps! http://forum.appliancepartspros.com/dryer-repair/25860-dryer-belt-diagrams.html Read More...
Scott September 28, 2011 for Model Number Whirlpool Duet dryer The idler pulley is screaming like a banshee. I sprayed the shaft with silicone, but that only helped for one load. Do I need to replace it or is there something else I can do. And if I replace it should I replace the belt at the same time?
1 Answer Hello Scott. Based on the information you provided, it sounds like the idler pulley WP691366 is bad and will need to be replaced. You can check the belt for wear. If there is some, it might be a good idea to replace it as well. Hope this helps. Read More...
Den September 13, 2011 for Model Number 110.62712101 Hi, I have an idler pulley with a pad (no wheel) how do I get the belt around the pad without splitting the pulley? Thanks
1 Answer Hello Den. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. Hope this helps. http://forum.appliancepartspros.com/dryer-repair/25860-dryer-belt-diagrams.html Read More...
Tom September 10, 2011 for Model Number ???? the idlerpulley came off the dryer. part number ap2911909. Kenmore 80 series. im not sure how to put it back on. I would apreciate your help. Tom
1 Answer Tom, Its a easy set up, Look at the base of the dryer, in front of the motor, you'll see two(2) slots formed in the base. With the pulley on top and away from the wall, insert the end of the idler The end of the idler pulley assembly into the slot farthest away from the cabinet wall. the two920 tabs on the bottom of the assembly will insert into the slot closest to the wall and you' can hold it in place until you insert the belt between the pulley and the metal shaft(the belt should be on the bottom side of the pulley in a loop) pull the belt until you can slip it over the drive pulley. Turn the drum 2 or 3 times by hand and slowly, so the belt centers up on the drum. You'll do fine. Thanks and Good Luck Read More...
Nick G. August 23, 2011 for Model Number LEQ9508LW0 My idler pulley has a sliding pad and not a wheel. Can I order an idler with a pad? I can't see it in the picture. Is an idler with wheel ok for my dryer? I would like to order a belt and an idler pulley. Thank you.
1 Answer Hello Nick! The belt is part number 341241. The idler pulley is part number WP691366. This is a replacement idler pulley and may look different than the original, however, this is the direct replacement and will work on your Whirlpool dryer model LEQ9508LW0. The manufacture offers a maintenance kit for your dryer part number 4392065. This kit contains the pulley, rollers, and the belt for a lesser price. Hope this information helps! Read More...
Isaac August 21, 2011 Hi, I need an Idler Pulley. I just need the wheel because It has a clip to remove the old one and install the new one. If I buy what you are selling, can I take off the wheel and re-use the old bracket?
1 Answer Hello Isaac! The manufacture only offers the idler pulley WP691366 as a fully assembled part. It would be recommended to replace the entire pulley with bracket and wheel. Thanks. Read More...
1 Answer Hello Louise. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. Hope this helps. http://forum.appliancepartspros.com/dryer-repair/25860-dryer-belt-diagrams.html Read More...
1 Answer Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. http://forum.appliancepartspros.com/dryer-repair/25860-dryer-belt-diagrams.html Read More...