Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Rotor Position Sensor Kit by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM12981945
Manufacturer Part Number: W10183157

Questions & Answers

For Whirlpool Rotor Position Sensor Kit (Part Number: OEM12981945)

1 Answer

Hello George. F then 50 flashes when the motor rotor
position sensor (RPS) senses no rotation.
? Does basket turn freely? If not, make sure
bottom shipping pack has been removed.
Determine cause of friction. This test checks the wiring to the motor and rotor
position sensor; and the motor and rotor position sensor
themselves.
NOTE: Drain water from tub.
1. See Activation of Manual Diagnostic Test Mode,
page 3 and check the motor and electrical
connections by performing the Spin test under
Manual: Motor, page 2. The following steps assumes
that this step failed.
2. Unplug washer or disconnect power.
3. Check to see if basket will turn freely.
? If basket turns freely, go to step 4.
? If basket does not turn freely, determine what is
causing the mechanical friction or lock up.
4. Remove the console to access the machine/motor
control assembly. See Accessing & Removing the
Electronic Assemblies, page 6.
5. Visually check that the P5 and P10 connectors are
inserted all the way into the machine/motor control.
? If visual checks pass, go to step 6.
? If visual checks fail, reconnect P5 and P10 and
repeat step 1.
6. Visually check that the P5 and P10 connectors are
inserted all the way into the machine/motor control.
? With an ohmmeter, verify resistance values.

Read More...

1 Answer

Chad,

If the unit is making a noise almost like a jet plane taking off then the issue would be in the bearings of the unit which would need to be replaced. The bearing part number is W10435302 and you will need a tool to remove the bearing W10447783

Read More...
Dry for Model Number WTW6600SW1

I have a whirlpool cabrio (2006) that was giving F51 codes about 10-15 minutes into a cycle. I originally thought it was the Motor Control Board and ordered that part. Once I put it on though, I still got the F51 error on the agitator part of the manual diagnostic. However, I was able to run through 3 full wash cycles (2 empty, 1 with towels) and the error didn't come up again. Looking for advice on if I really solved the problem or if it indicates I need to replace the RPS sensor itself?

1 Answer

Hello Dry. According to the manufacture, it is either the RPS sensor or the wiring harness on the unit. The motor control board is not going to solve the issue with the F51.

Read More...

1 Answer

Hello Pete. oL flashes when the machine/motor control
detects a load size that exceeds the
washer’s capacity OR basket can not
disengage. This may signify:
? Load size exceeds washer capacity.
Remove excess laundry, then restart cycle.
? Mechanical friction on drive mechanism,
not allowing the basket to disengage.
If it does this with the unit not loaded, you will need to order and replace the suspension springs on the unit.

Read More...

1 Answer

Hello Brychael. F then 50 flashes when the motor rotor position sensor (RPS)
senses no rotation.
? Does basket turn freely? If not, make sure bottom shipping
pack has been removed. Determine cause of friction.

Read More...

1 Answer

Hello Ted,

If the Rotor positon sensor needs to be replaced you would want to install kit W10183157 which has the wiring harness that comes with it.

Read More...

1 Answer

Hello Vic,

The F1 error code indicates a primary control failure. Per tech sheet it states to replace machine/motor control WPW10189966.

Read More...

1 Answer

Hello Bata,

The unit will need to have new tub seal and bearing kit W10435302. Or you can replace outer tub. The bearings have gone out on unit. If you replace just the tub seal and bearing kit you will also need to order a bearing removal tool W10447783.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google